510130
6
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
EN
6 Ferm
space (free of iron powder, dust and paint).
• Place the welding appliance on a firm and flat
surface and at least 20 cm from the wall.
• Protect the welding appliance against rain and
strong sunlight.
The welding mask
Fig. 2
• Slide the handle on the welding mask until it
locks.
• Place the light glass (protective glass) in front
of the dark welding glass. Slide both glasses
in front of the opening.
• Make sure that the glasses are positioned so
that no (harmful) light can now penetrate the
opening.
• Replace the light protective glass when the
view of the workpiece becomes insufficient
during welding. Replacing the dark welding
glass is considerably more expensive than
replacing the light protective glass.
Fitting new electrodes
The electrode consists of a metal core enclosed
by a coating. At one end of the electrode the core
is not covered by the coating.
• Press the handle of the electrode holder
against
the spring.
• Place an electrode with uncoated end (± 2 cm)
in the electrode holder. Make sure that the
non-coated part makes good contact with the
metal part of the electrode holder (electrode
not pushed too far in the electrode holder).
• Release the handle of the grip. The electrode
is now fixed.
N.B! Do not allow the electrode to burn to
lengths shorter than ± 5 cm because of
overheating and/or the deformation of the
electrode holder. The burnt up electrode
will then be difficult to remove.
Removing used electrodes
Press the grip of the electrode holder against the
spring so that the burnt up electrode can fall from
the holder.
N.B! Do not remove the electrode from
the holder by hand. The electrode is very
hot!
N.B! Watch where the waste electrode
falls to prevent a fire hazard and possible
injury.
Installation
Fig. 4
Only an authorized electrician is allowed
to connect the correct plug to the welding
machine.
• Placetheblockingscrew(A)inthecorrect
position for 230V(4a) or 400V (4b). (See Fig. 4
a,b,c)
• Warning:Whentheswitchisonposition
“230V”, the wiring L, N and PE in the power
cord should be connected with the mains
power supply. When the switch is on position
“400V”, the wiring L1, L2 and PE in the power
cord should be connected with the mains
power supply. Above that a suitable fuse has
to be used.
4. Operating
Before use:
a. General information about electric arc welding
b. The electrode
c. Protective clothing
d. Face protection
e. Working environment
a. General information about electric arc
welding
The temperature of the arc amounts to approx.
7000° Celsius, so the end of the electrode and the
workpiece fuse. For as long as the arc is
maintained, the electrode will melt and supply the
necessary welding material to the parts to be
joined. The distance between the electrode and
the workpiece must be as short as possible
(approx. 1.5 - 4 mm) depending on the diameter
and type of electrode. The current needed for
welding is supplied by the welding appliance.
The power required by the welding appliance
depends on the work to be done.
Make sure that the electrodes are completely dry,
as moist electrodes cause problems. If the
electrode sticks to the workpiece during welding
your current intensity is set too low.
b. The electrode
• The electrode consists of a metal core
enclosed by a coating. The coating has the
most important purpose of protecting the
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm WEM1035 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm WEM1035 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info