510130
5
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
EN
5
Ferm
• The slag to be chipped off is sometimes
glowing hot and can cause serious eye injuries
during removal. Always wear protective
goggles and gloves.
• Ultraviolet radiation can burn your skin during
welding. So always wear suitable protective
clothing.
• Your welding appliance is protected against
overloading. The welding appliance therefore
automatically switches off if it overloads. The
welding appliance automatically switches on
again after it has cooled sufficiently.
• During welding and cooling your workpiece
can deform due to stresses. Always bear this
in mind.
• Only the welding cables included in the
delivery kit may be used (Ø 10
mm
2
rubberized
welding cable).
• Special regulations apply to areas at risk of
fire or explosions.
• Welded connections that are exposed to high
stress and which must fulfill certain safety
requirements may only be carried out by
specially trained and certified welders. Some
examples are: Pressure vessels, slide rails,
tow couplings, etc.
• Important: Always connect the ground terminal
as close as possible to the weld spot in such a
way that the welding current can take the
shortest possible path from the electrode to
the ground terminal. Never connect the
ground terminal to the housing of the welding
device! Never connect the ground terminal to
grounded components that are located far
away from the workpiece, e.g., to a water pipe
in another corner of the room. Otherwise, the
protective conductor system of the room in
which you are welding could become
damaged.
• The fusing of the supply lines to the power
outlets must correspond to regulations (VDE
0100). Protective contact outlets may be fused
with a max of 16A (types and technical data:
RT14-20, Ø 10 x 38, AC 400 V 16A. IEC
60269. slow blow. Manufacturer: Chint) (fuses
or line-protection switches). Higher amperage
fuses can lead to burnt cables or fire damage
to the building.
Electrical safety
Switch off the machine at once if:
• There is a defect in the mains plug,
power cable or there is damage to the
cable.
•Defectiveswitch.
•Youseesmokeorsmellburnt
insulation.
Warning! Depending on the supply mains
conditions at the point of connection, the
welding power source may cause
interference to the supply to other
electricity users. If there is any doubt
about this question advice should be
sought from the electricity supply
authority.
• Make sure that the welding appliance and
electric wiring connections are properly made.
Any likelihood of electric shock can endanger
life.
• Always ensure good connections, both of the
electrode holder and the earth terminal.
• Do not allow electrical cables to be damaged
by pulling. Disconnect cables before you move
the welding appliance.
• Avoid contact with the electrically conductive
part of the welding appliance, the electrode
holder and the earth terminal.
• Always check that your mains voltage
corresponds to the value on the type plate of
the machine.
• With the replacement of cables or plugs:
Throw away old cables or plugs as soon as
they have been replaced by new ones.
Inserting a loose cable plug in a plug socket is
dangerous.
• For all welding appliances working on 230
Volts use at least 16 Ampere fusing
• When use is made of extension leads: Use
only an approved extension lead that is
suitable for the machine power. The cores
must have a diameter of at least 1.5 mm
2
. Roll
the cord fully out if the extension cord is on a
reel.
• Only allow qualified electricians to work on the
supply voltage end, e.g., on cables, plug-in
connectors, outlets, etc.
3. Mounting accessories
Make sure that the plug has been
removed from the plug socket during the
assembly of accessories.
Installation of the machine
• Install the welding appliance in a dry and clean
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm WEM1035 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm WEM1035 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info