510130
8
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
EN
8 Ferm
workpiece as if you were striking a match. This
is the best way to start the welding arc. Do not
strike the workpiece with the electrode. This
will damage the electrode and impede the
creation of the welding arc.
• After creating the welding arc immediately try
to keep the distance between point of the
electrode and the workpiece equal. Keep this
distance equal to the diameter of the
electrode. Keep this distance as constant as
possible during welding.
• Move the electrode in a gradual pulling
movement over the workpiece.
• Keep the angle between electrode and
workpiece between 60° and 70° in the
direction of movement.
• When the welded joint has been made, break
the welding arc by removing the electrode
from the workpiece.
• Switch off the welding appliance.
N.B. If you leave the welding appliance
on, the likelihood is great that the
electrode will make contact (through the
work bench) with the earth cable and
spontaneously start to weld.
• Remove the slag from the welded joint with a
scaling hammer.
Take care for hot flying metal particles.
Always wear protective goggles.
• Never weld over slag residues: the slag forms
an insulating and contaminated layer, and as a
result weakens the weld (so-called slag
inclusion).
• Brush the weld clean using a wire brush.
N.B. The workpiece is still at a very high
temperature.
Do not leave the hot workpiece
unattended.
Indicator lamp temperature
Fig.1
When the temperature of the welding appliance
becomes too high, the built-in thermostat will
switch off (indicator light comes on). The built-in
ventilator cools the machine. After cooling the
lamp goes off again.
Preferably allow the machine a sufficient time to
cool down; with intensive welding the likelihood is
great that the thermal cut-out will trigger again
after a few minutes.
5. Service & maintenance
Make sure that the machine is
disconnected before carrying out any
maintenance.
This machine has been designed to operate over
a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Malfunction
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
The welding appliance is not working.
• Earth terminal does not have good contact
with the workpiece.
• Electrode is not properly positioned in its
holder.
• Thermalcut-outswitchedoff.
• Fusingdefective(inmeterbox).
• Thecableisbroken.
• Theswitchisdefective/contactyourdealer.
Electrode continues to ‘stick’ to the
workpiece.
• Use the right type of electrode (universal)
• Current intensity too low/turn button 3
clockwise
Electrode is orange-red.
• Current intensity too high for this type of
electrode/turn button 3 anti-clockwise
Electrode spatters excessively and makes a
lot of noise during welding.
• Current intensity too high/turn button 3 anti-
clockwise
The machine is too hot; indicator lamp is on.
• The ventilation slots are blocked/clean them
with a dry cloth; wait a few minutes until the
lamp goes off again.
Repairs and servicing should only be
carried out by a qualified technician or
service firm.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm WEM1035 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm WEM1035 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info