Ferm 67
Sørg for at maskinen ikke står under strøm, når der udføres
vedligeholdelsesarbejder på mekanikken.
Maskinerne fra Ferm er udviklet til at fungere længe uden problemer med et minimum af
vedligeholdelse. Ved at rengøre maskinen regelmæssigt og behandle den korrekt, bidrager De
til en længere levetid for maskinen.
Hjælp
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til at
fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammoniak,
osv. Den slags stoffer beskadiger kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres
på en genbrugsplads.
Garanti
Garantibetingelser er beskrevet på det separat vedlagte garantibevis.
• Den elektroniske motor bliver varm: • Rengør ventilationsåbningen
• Støvet bliver ikke opsamlet: • Støvposen er fuld / tøm støvposen
• Slibepapiret er fyldt med klæbestof/ • Maling eller klæbestof er ikke tørt.
maling eller lignene materiale: • Nogle former for maling klæber mere til
slibepapir end andre / rengør ofte
slibepapiret
5. VEDLIGEHOLDELSE
UK
D
NL
F
E
P
I
S
SF
N
DK
6Ferm
The sandpaper (5) is fixed by Velcro fastener to facilitate the replacement.
• Simply pull off the sanding paper
• Press the new one in the centre of the sanding sole (6)
Coarse sand-paper (grain 50) removes in general the bigger part of the material and fine sand-
paper (grain 120) is used for the finishing.
Replacing the sanding sole
The sole has to be replaced when the Velcro has been worn out.
Before replacing the sanding sole disconnect the sander from the mains.
• Remove the sandpaper of the sole.
• Remove the screws which the sole is fixed to the sander.
• Remove the sole.
• Install the new sole on the sander.
• Tighten the screws well.
Operation
• Push in the on/off switch (1) to start the machine.
• By adjusting the adjusting wheel (8) you can regulate the speed.
• The ventilating apertures (4) on the housing must remain clear to ensure optimum cooling
of the motor.
• Move the sander over the surface of your workpiece.
• Let loose the same on/off switch to stop the machine.
• The on/off switch can be blocked in position “ON” by pushing the lock-on button (9) on the
side, while you keep pushing the on/off switch. The machine can be stopped by briefly
pushing the on/off switch again.
Prevent pushing too much on the machine during sanding. Excessive sanding
pressure does not lead to increased sanding capacity, but increases wear of the
machine and the sandpaper.
Grips
The sander is equipped with two grips: a handle at the front side and one on the back side.
Always hold the sander with both hands on the handles, so as to gain the best possible control
over your sanding operations. Besides you do not risk to become in touch with the moving
parts.
Sanding
The sanding sole of the sander executes small circular movements. Trough this you will get an
even surface without marks.
4. USE
GB
D
NL
F
E
P
I
S
SF
N
DK
