696805
9
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
Installation manual
9
3.3.1 C11, wall terminal
For a facade or wall outlet use a wall terminal (see g. 1.0 C11).
Depending on the calculation this can be a diameter of 130/200mm
or 100/150mm.
3.3.2 C31, roof terminal
For a at or pits roof outlet use a long roof outlet with a diameter of
100/150mm (see g. 1.0 C31)
3.3.3 C91, existing chimney
You can also connect to an existing replace chimney. The existing
chimney functions then as air supply and a exible stainless steel
tube drawn through the chimney carries the ue gases. The exible
stainless steel tube of Ø100mm must have a CE mark have up to
600°C.
Use the short chimney outlet. (See g. 1.0 C91).
The chimney must have the following conditions:
The channel of the chimney must be at least 150x150mm.
There should be no more than one device on a chimney.
The chimney must be in good condition:
o No leakage
o Well cleaned
For more information about connections to existing chimneys, ask
the installation manual “chimney connection set”.
4 Preparation and installation
instructions
4.1 Gas connection
The gas connection must comply with the applicable local
standards. We advise using a Ø15mm gas connection directly from
the gas meter to the appliance, with a shut-off valve in the proximity
of the appliance, which must always be freely accessible. Position
the gas connection so that it is easily accessible at all times for
service and that the burner unit can be disassembled. (See g.
8.0-C and dimensional drawing 16.2 for position of the gas
connection).
4.2 Electrical connection
The power supply must comply with the applicable local standards.
A wall socket 230VAC/50Hz must be installed near the re. For
power supply make use of the included plug adapter. See g 2.0 for
the wiring diagram of this connection and the LED Symbio module.
A = Plug adapter 6V
B = Micro switch
C = Spark transformer
D = LED Symbio module
E = Slider
4.3 Preparing the re
Remove the re from its packaging. Open the operation door
(see g. 3.0), take the packaged parts from the re and
remove the bolts in the bottom plate.
Prepare the gas connection on the regulator. See g. 8.0-C
and dimensional drawing 16.2.
4.4 Positioning the re
Take into account the installation requirements and the minimum
distances around the replace. (See Chapter 3).
4.5 Installing the ue materials
When penetrating a non-combustible wall or ceiling the
opening must be at least 5mm larger than the diameter of the
discharge material. At a combustible wall or ceiling is this
100mm larger than the diameter of the drainage material.
Horizontal sections should be installed with a slope towards
the re (3 degrees).
Build the system from the re. If this is not possible you can
make use of an extendable adapter section.
For truing up the exhaust system use the 0,5m. pipe, which
can be shortened and ensure that the inner pipe is always
2cm longer than the outer pipe.
Parts, which are shortened, must be secured with a
self-tapping screw.
Wall and roof terminals can also be cut.
Do not insulate but ventilate built-in ue material (approx.
100cm²).
5 Removing the glass
5.1 Front glass
Remove the front frame. See g. 4.0.
Slightly loose the screws of the glass support under.
See g. 4.1.
Slightly loose the nuts of the upper glass support and remove
it. See g. 4.2.
Remove the front glass. See g. 4.3.
For replacing the front glass repeat the steps in reverse
order.
> Please note:
Clean all ngerprints on the glass; otherwise they will burn in once
the re is used.
5.2 Side glasses
For cleaning only it’s not necessary to remove the side glasses.
Only remove the front glass. See Chapter 5.1.
Remove the side panel. See g. 5.0.
Slightly loose the screws of the glass support under.
See g. 5.1.
Slightly loose the nuts of the upper glass support and
remove it. See g. 5.2.
Remove the side glass. See g. 5.3.
> Please note:
Clean all ngerprints on the glass; otherwise they will burn in once
the re is used.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Faber-Vejen

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Faber Vejen bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Faber Vejen in de taal/talen: Engels als bijlage per email.

De handleiding is 9,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Faber Vejen

Faber Vejen Installatiehandleiding - Nederlands - 24 pagina's

Faber Vejen Installatiehandleiding - Deutsch - 28 pagina's

Faber Vejen Installatiehandleiding - Français - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info