612699
77
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
77 of 94
ELM327
ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
the default setting for PP 0E turns these hand-shaking
signals off, so you will need to change that in order to
use them.
We are often asked about connecting the ELM327
to 3.3V logic, which is quite popular. Many hope that
they can just insert a resistor or two and have it work.
Unfortunately, that is not the case, mostly because the
ELM327 has Schmitt waveshaping on the RS232 Rx
input (pin 18), and so may need as much as 4V for a
high input (although it often works with less). To
ensure that there’s enough voltage, we recommend
using a level translator circuit such as the TXB0102
from Texas Instruments (www.ti.com), the ST2129
from ST Microelectronics (www.st.com), or the Analog
Devices (www.analog.com) ADuM1201 as shown
here. We have been using the ADuM1201 with the
Raspberry Pi lately, because it offers galvanic isolation
(to 2500 Vrms) in addition to the level translation, so
protects the Pi from occasional wiring problems. Note
that for complete isolation you must use separate
commons for the 5V and the 3.3V power supplies. The
one disadvantage with the ‘1201 over the others is that
it draws about 1 mA, which can be an issue if you are
trying to use the low power mode with your ELM327.
A popular question that we receive is “Can I
upgrade my firmware with a file download?”. The
answer to this is no, the ELM327 can not be upgraded
in this way - your integrated circuit must be replaced.
The next question which usually follows is “Can I
simply replace an old ELM327 chip with a new one to
upgrade the firmware?”
The answer to this last question is basically yes.
We say basically because there was a change
between versions 1.3a and 1.4b when we added the
power control feature. This change modified how pins
15 and 16 were used (they took on dual roles), and
that may affect your circuit.
If your circuit board is older and used an earlier
version of our chip (ie pre v1.4b), then you have to
look at what pins 15 and 16 were used for. Almost all
of the early boards followed our example and left pin
16 open, and pin 15 tied to +5V. If your circuit did this,
there is no problem - you may simply replace the old
chip with a new one.
If your circuit board used pins 15 and 16 for
handshaking with a microprocessor or other device,
then you may need to take extra steps. Usually this
only requires turning off the low power control by
setting b7 of PP 0E to 0.
If you are replacing a v1.4b or a v2.0 integrated
circuit with a newer one, then there are no concerns.
Please note that there are several clone products
available that use integrated circuits that mimic the
ELM327 at a software level. They do not necessarily
mimic the hardware. For this reason, you should not
replace a clone chip with a genuine ELM chip, unless
you are absolutely certain that all 28 pins of the
integrated circuits are identical.
7
9
+3.3V
+5V
n.c.
+5V
your microprocessor
Rx
Rx
ADuM1201
Busy
RTS
327
8
1
2
3
4
5
6
7
8
+5V
+3.3V
Microprocessor Interfaces (continued)
Upgrading Versions
77

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info