810366
351
Verklein
Vergroot
Pagina terug
1/396
Pagina verder
Wheels and tyres
349
Changing a wheel
Fig.228 Crossbar: mounting the jack on
the vehicle.
Rest the jack (vehicles tools) on rm ground.
If necessary use a large, strong board or similar
support. If the surface is slippery (for example
tiles) place the jack on a rubber mat or similar
to prevent it from slipping ››› .
Look on the strut for the mark of the jack
support point (sunken area) closest to the
wheel to be changed ›››Fig.227.
Turn the jack crank handle, located below
the strut support point, to raise it until the
tab 1 ›››Fig.228 is below the housing that
is provided.
Align the jack so that the tab 1“grips”
onto the housing provided on the cross mem-
ber and the mobile base 2 is resting on the
ground. The base plate 2 should fall vertically
with respect to the support point 1 .
Continue turning the jack until the wheel is
slightly lifted o the ground.
WARNING
The factory-supplied jack is only designed
for changing wheels on this model. On no
account attempt to use it for lifting heavier
vehicles or other loads. Risk of injury.
Make sure the jack remains stable. If the
surface is slippery or soft, the jack could slip
or sink, respectively, with the consequent
risk of causing injuries.
Lift the vehicle using only the jack supplied
from the factory. Other jacks, even those ap-
proved for other CUPRA models could slip,
with the consequent risk of injury.
Place the jack only at the support points
provided on the strut and align it. Otherwise,
the jack could slip because it does not have
suicient grip on the vehicle: risk of injury!
You should never place a body limb such as
an arm or leg under a raised vehicle that is
solely supported by the jack.
If you have to work underneath the vehi-
cle, you must use suitable stands additionally
to support the vehicle, there is a risk of acci-
dent!.
Never raise the vehicle if it is tilting to one
side or the engine is running.
Never start the engine when the vehicle is
raised. The vehicle may come loose from the
jack due to the engine vibrations.
NOTICE
The vehicle must not be raised on the
crossbar. Place the jack only at the support
points provided on the strut and align it. Oth-
erwise, the vehicle may be damaged.
Any type of load or weight applied to the
external trim/door will (stepped on, tting
the jack, resting heavy objects, etc.) can
cause damage to it. CUPRA accepts no re-
sponsibility for any damages caused by im-
proper use of the external trim or body.
Removing and installing a wheel
Change the wheel after loosening the wheel
bolts and raising the vehicle with the jack.
When removing/tting the wheel, the rim may
hit and damage the brake disc. For this reason,
please take care and get a second person to
assist you.
Taking o the wheel
Unscrew the bolts with the wheel wrench
and place them on a clean surface.
Remove the wheel.
Putting on the spare wheel
Check the direction of rotation of the tyre
›››page350.
351

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cupra Formentor - 2022 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cupra Formentor - 2022 in de taal/talen: Engels als bijlage per email.

De handleiding is 7.81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Cupra Formentor - 2022

Cupra Formentor - 2022 Gebruiksaanwijzing - Nederlands - 424 pagina's

Cupra Formentor - 2022 Gebruiksaanwijzing - Deutsch - 415 pagina's

Cupra Formentor - 2022 Gebruiksaanwijzing - Français - 436 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info