650Tazur
9
ENGLISH
DAB manual tuning
It is also possible to manually tune to DAB stations if you know their
transmission frequencies.
1. Press and hold the ‘Info’ button to initiate manual tuning (by frequency).
Manual tuning will be displayed on the front.
2. Use the buttons to change the radio frequencies. Allow the unit
a few seconds while it registers the transmission group which will be
displayed below the frequency range on the second line.
3. Press the ‘Select/Mode’ button to select the transmission group. Use
the buttons to browse through available stations from the chosen
transmission group.
4. Press the ‘Select/Mode’ button to select the desired station. The unit
will go back to ‘auto’ DAB tuning.
5. You may rapidly browse through available channels by holding down
either the or buttons.
Note: To exit manual tuning mode without selecting a station, press and
hold the ‘info’ button again.
DAB+
The 650T is compatible with both DAB (MP2 audio compression) and
DAB+ (AAC+ audio compression) broadcasts. A ‘+’ symbol will appear on
the far right of the front panel display when a DAB+ broadcast is being
received.
DAB Secondary services
Station with secondary services will be indicated by a ‘’ on the far right
first line of the display. DAB secondary services are part-time broadcasts
on the DAB network, such as some BBC LW transmissions.
1. Press the ‘Select/Mode’ button to tune in and access the secondary
services.
2. Press the ‘Select/Mode’ button to exit the secondary services and
revert to the primary station.
Connecting and using a SIRIUS Connect
Home Tuner (SIRIUS Ready version only)
The 650T can be used in conjunction with a compatible SIRIUS receiver
module such as the SIRIUS Connect Home Tuner SC-H1. This module
allows you to subscribe and listen to any station on the SIRIUS satellite
radio network.
Please carefully read the instructions included with your particular tuner,
paying attention to antenna configuration.
Note: The 650T can power the SIRIUS Ready module via the SIRIUS socket
and no separate power adaptor is required.
1. Ensure your 650T is powered Off using the power switch on the rear
panel. Connect the SIRIUS module using the supplied DIN cable.
Connect the AC power supply to the Home Tuner, and confirm that the
LED indicator is on.
2. Power On your 650T from the power switch on rear panel.
3. Press the Band button and select the SIRIUS mode.
Subscribing to services
First, make a note of your Home Tuner’s identification number (SID). This
number may be obtained by selecting SIRIUS mode, and holding down the
Info button on the front of the unit. The SID may also be found an a label
located on the Home Tuner module.
To activate your subscription, please call 1-888-539-SIRIUS (1-888-539-
7474) .
Alternatively, visit www.sirius.com and click Activate. Follow the online
instructions to register your module.
Positioning the antenna
The antenna must be positioned in such a way that the tuner can receive
the best possible signal from the transmission satellite. The direction of
the antenna depends on your geographical location in the United States.
Location Antenna Direction
Northwestern US or western Canada East
Midwestern US or central Canada Directly above
Northeastern US or eastern Canada West
Southwestern US North-east
South central US North
Southeastern US Northwest
The LED indicator on the receiver module will turn green when you have
sufficient signal strength.
Manual tuning
In this mode, you can navigate through all subscribed stations using the
buttons.
1. Press the Band button to change to SIRIUS mode.
2. Use the buttons to browse/tune through available stations. If the
station you wish to listen to is not present, you may need to add it to
your subscription. Call 1-888-539-SIRIUS for more information.
3. To store a station as a preset, see ‘Setting Presets’ on previous section.
4. You may rapidly step through the subscribed and available channels by
holding down either the or buttons.
Direct tuning
You can tune directly to a channel of your choice.
1. Press the Band button to change to SIRIUS mode.
2. Press the Select/Mode button on the remote control. The display will
show 'SELECT CHANNEL CH---'.
3. Enter the channel number you wish to tune to using the numerical keys
on the remote.
4. Press the Select/Mode button to confirm.
