460547
25
Verklein
Vergroot
Pagina terug
1/152
Pagina verder
English | 25
Bosch Power Tools 2 609 004 157 | (11.5.10)
Sawing
f Use undamaged faultless saw blades only.
Deformed, blunt saw blades or saw blades
that are otherwise damaged can break.
f When sawing light building materials, ob-
serve the statutory provisions and the rec-
ommendations of the material suppliers.
f Plunge cuts may only be applied to soft ma-
terials, such as wood, gypsum plaster
boards, etc.!
Before sawing with HCS saw blades in wood,
particle board, building materials, etc., check
these for foreign objects such as nails, screws,
or similar. If required, remove foreign objects or
use BIM saw blades.
Separating
Note: When separating wall tiles take into con-
sideration that the application tools/accessories
wear heavily when used for longer periods of
time.
Sanding
The removal rate and the sanding pattern are
primarily determined by the choice of sanding
sheet, the preset oscillation rate and the ap-
plied pressure.
Only flawless sanding sheets achieve good
sanding capacity and extend the service life of
the machine.
Pay attention to apply uniform sanding pres-
sure; this increases the working life of the sand-
ing sheets.
Intensifiying the sanding pressure does not lead
to an increase of the sanding capacity, but to in-
creased wear of the machine and the sanding
sheet.
For precise on-the-spot sanding of edges, cor-
ners and hard to reach areas, it is also possible
to work only with the tip or an edge of the sand-
ing plate.
When selectively sanding on the spot, the sand-
ing sheet can heat up considerably. Reduce the
orbital stroke rate and allow the sanding sheet
to cool down regularly.
A sanding sheet that has been used for metal
should not be used for other materials.
Use only original Bosch sanding accessories.
To reduce the dust exposure and achieve better
working results when sanding, use dust extrac-
tion as far as possible.
Scraping
For scraping, select a high oscillation rate.
Work on a soft surface (e.g. wood) at a flat ange,
and apply only light pressure. Otherwise the
scraper can cut into the surface.
Temperature-dependent Overload Protection
When using the machine as intended for, it can-
not be subject to overload. In case of excessive
load or when not within the permitted battery
temperature range of –20 °C to +65 °C, the ma-
chine switches off. In case of overload, the bat-
tery charge-control indicator 4 will additionally
flash red for a few seconds.
After an automatic shut-off, switch the machine
off. Wait until the battery temperature is within
the allowable range before switching the ma-
chine on again.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Store the battery only within a temperature
range between 0 °C and 45 °C. As an example,
do not leave the battery in the car in summer.
A significantly reduced working period after
charging indicates that the battery is used and
must be replaced.
Observe the notes for disposal.
OBJ_BUCH-1170-002.book Page 25 Tuesday, May 11, 2010 3:36 PM
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PMF 10,8 LI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PMF 10,8 LI in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 10,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info