544038
31
Verklein
Vergroot
Pagina terug
1/346
Pagina verder
English | 31
Bosch Power Tools 1 609 929 U75 | (19.7.10)
Working Advice
General Sawing Instructions
f For all cuts, it must first be ensured that the
saw blade at no time can come in contact
with the fence, screw clamps or other ma-
chine parts. Remove possibly mounted aux-
iliary stops or adjust them accordingly.
Protect the saw blade against impact and shock.
Do not subject the saw blade to lateral pressure.
Do not saw warped/bent workpieces. The work-
piece must always have a straight edge to face
against the fence.
Long workpieces must be underlaid or support-
ed at their free end.
Marking the Cutting Line (see figure J)
A laser beam indicates the cutting line of the
saw blade. This allows for exact positioning of
the workpiece for sawing, without having to
open the retracting blade guard.
For this, switch the laser beam on with the
switch 20.
Align the cutting mark on your workpiece
with reference to the right-hand edge of the
laser line.
Position of the Operator (see figure K)
f Do not stand in a line with the saw blade in
front of the machine. Always stand aside of
the saw blade. This protects your body
against possible kickback.
Keep hands, fingers and arms away from the
rotating saw blade.
Do not cross your arms when operating the
tool arm.
Permissible Workpiece Dimensions
Maximal workpiece sizes:
Minimal workpiece sizes
(= all workpieces that can be clamped left or
right from the saw blade with the supplied ma-
terial clamp 14): 100 x 40 mm (length x width)
Cutting capacity, max. (0°/0°): 50 mm
Cutting Off
Firmly clamp the workpiece as appropriate
for its dimensions.
Adjust the requested horizontal and/or verti-
cal mitre/bevel angle.
Switch on the machine.
Press lever 3 and slowly guide the tool arm
downward by handle 1.
Saw through the workpiece applying uniform
feed.
Switch off the machine and wait until the
saw blade has come to a complete stop.
Guide the tool arm slowly upward.
Replacing the Insert Plate
The red insert plate 7 can become worn after
long use of the power tool.
Replace defective insert plates.
Bring the power tool into the working posi-
tion.
Unscrew screws 8 using a Phillips screwdriv-
er and remove the old insert plate.
Insert the new insert plate and and screw all
screws 8 in again.
Sawing Profile Strips
Profile strips/mouldings can be sawn in two dif-
ferent ways:
Always make trial cuts with the mitre angle set-
ting first on scrap wood.
Mitre/Bevel Angle Height x Width
Horizontal Vertical
50 x 110 mm
45° 0°
50 x 76 mm
45°
37 x 110 mm
45° 45°
37 x 76 mm
– Placed against the fence
– Lying flat on the saw
table
OBJ_BUCH-880-004.book Page 31 Monday, July 19, 2010 11:56 AM
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PCM 7 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PCM 7 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 20,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info