544038
30
Verklein
Vergroot
Pagina terug
1/346
Pagina verder
30 | English
1 609 929 U75 | (19.7.10) Bosch Power Tools
Clamping the Workpiece (see figure F)
To ensure optimum working safety, the work-
piece must always be firmly clamped.
Do not saw workpieces that are too small to
clamp.
Press the workpiece firmly against the
fence 6.
Insert the material clamp 14 provided into
one of the holes 27 intended for it.
Loosen the wing bolt 33 and adapt the mate-
rial clamp to the workpiece. Tighten the wing
bolt again.
Firmly clamp the workpiece by turning the
threaded rod 34 in clockwise direction.
Loosening the Workpiece
To release the material clamp, turn the
threaded rod 34 in anticlockwise direction.
Adjusting the Cutting Angle
f When adjusting the cutting angle, never ac-
tuate the On/Off switch 19. Danger of injury
if the machine should accidentally start.
f Before sawing, always tighten the clamping
lever 25. Otherwise the saw blade could be-
come jammed in the workpiece.
Adjusting Horizontal Mitre Angles
(see figure G)
The horizontal mitre angle can be set in the
range from 46° (left side) to 46° (right side).
Release clamping lever 25, if tightened.
This allows the saw table to move freely.
Turn the saw table 11 left or right by handle
9 until the angle indicator 35 indicates the
desired mitre angle.
Tighten clamping lever 25 again.
For quick and precise setting of often used mi-
tre angles, the saw table 11 engages at the de-
tents of the following standard angles:
–45°/ –30°/ –22.5°/ –15°/
0°/ 15°/ 22.5°/ 30°/ 45°
Adjusting Vertical Bevel Angles (see figure H)
The vertical bevel angle can be set in the range
from 0° to 45°.
Loosen the clamping lever 23.
Tilt the tool arm by the handle 1 until the an-
gle indicator 36 indicates the desired bevel
angle.
Hold the tool arm in this position and retight-
en the clamping lever 23.
For quick and precise setting of the standard
angles 0° und 45°, end stops are provided on
the housing.
Loosen the clamping lever 23.
For this, tilt the tool arm by the handle 1 to
the stop toward the right (0°) or to the stop
toward the left (45°).
Retighten the clamping lever 23 again.
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On (see figure I)
–To start the machine, press the On/Off
switch 19 and keep it pressed.
Note: For safety reasons, the On/Off switch 19
cannot be locked; it must remain pressed during
the entire operation.
The tool arm can only be guided downward
when pressing lever 3.
–For sawing, you must additionally press lever
3 in addition to actuating the On/Off switch.
Switching Off
–To switch off the machine, release the
On/Off switch 19.
OBJ_BUCH-880-004.book Page 30 Monday, July 19, 2010 11:56 AM
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PCM 7 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PCM 7 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 20,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info