79225
22
Verklein
Vergroot
Pagina terug
1/153
Pagina verder
English - 5
Do not connect the chain saw to mains be-
fore it is completely assembled.
Always use gloves when handling the
chain.
Chain and chain bar Assembly
1. Unpack all parts carefully.
2. Place the chain saw on any suitable flat surface.
3. Slide the chain 9 in the slot around the chain
bar 10. Ensure chain is in correct running direc-
tion by comparing with chain symbol 19.
4. Fit the chain onto the drive sprocket 20 and guide
the chain bar 10, so that the fastening bolt 15 and
the two guide fins 17 fit into the keyway of the
chain bar 10, and that the chain tensioning
peg 16 fits into the respective hole of the chain
bar 10. If necessary, turn the tensioning knob 14
to bring tensioning peg 16 in alignment with the
hole in the chain bar 10. Check if all parts are
seated properly and hold chain and chain bar in a
level position. (see figure )
5. Turn the tensioning knob 14 until all the slack is
taken up in the chain.
6. Fit cover plate 13. (see figure )
7. Handtighten locking knob 12 on fastening bolt 15.
(see figure )
If too tight then the chain can lose ten-
sion during use.
The locking knob must only lightly
clamp the chain bar.
Tensioning chain
Always check the chain tension before use, after the
first cuts and regularly during use, approx. every
10 minutes. Upon initial operation, new chains can
lengthen considerably.
The chain life of the saw chain mainly depends upon
sufficient lubrication and correct tensioning.
Avoid tensioning the chain if it is hot, as this will
cause the chain to become overtensioned when it
cools down.
1. Place the chain saw on any suitable flat surface.
2. Check if the chain links are correctly located in
the slot around the chain bar 10 and drive
sprocket 20.
3. Loosen locking knob 12 until it is just holding
chain bar in position (do not remove!).
4. Turn tensioning knob 14 clockwise until the cor-
rect chain tension is reached. The turning action
forces the chain bar 10 forward via the chain ten-
sioning peg 16.
5. The correct chain tension is reached when the
chain 9 can be raised approx. 3 4 mm from the
chain bar in the centre. This should be done by
using one hand to raise the chain against the
weight of the machine.
6. If the chain 9 is overtensioned, slightly turn the
tensioning knob 14 anti-clockwise and re-check
chain tension. Re-adjust chain tension as de-
scribed if necessary.
7. Handtighten locking knob 12 on fastening bolt 15.
If too tight then the chain can lose ten-
sion during use.
The locking knob must only lightly
clamp the chain bar.
Important: The chain saw is not supplied
filled with oil. It is essential to fill with oil
before use. Never operate the chain saw
without chain oil or at an empty oil tank
level, as this will result in extensive dam-
age to the product.
Chain life and cutting capacity depend on optimum
lubrication. Therefore, the chain is automatically
oiled during operation via the oil outlet 18.
Filling oil tank:
Set chain saw on any suitable surface with oil
filler cap 4 facing upward.
Clean area around the oil filler cap 4 with cloth,
unscrew cap.
Add Bosch biodegradable chain saw oil until res-
ervoir is full.
Avoid dirt or debris entering oil tank, refit oil filler
cap 4 and tighten.
Important: To allow venting of the oil res-
ervoir,small breather channels are pro-
vided between the oil filler cap, to prevent
leakage ensure machine is left in a hori-
zontal position (oil filler cap 4 uppermost)
when not in use.
It is important to use only the recom-
mended biodegradable oil to avoid dam-
age to the chain saw. Never use recycled/
old oil. Use of non approved oil will invali-
date the warranty.
Observe the correct mains voltage! The voltage
of the power source must agree with the value given
on the nameplate of the machine. Machines desig-
nated for 230 V can also be operated with 220 V.
Assembly/Tensioning Chain
A1 A2 A3
A1
A2
A3
A1 A2 A3 C
Lubrication
Starting and Stopping
B
F 016 L70 540.book Seite 5 Montag, 9. Februar 2009 2:37 14
22 • F 016 L70 540 • TMS • 29.01.09
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GKE 40 BCE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GKE 40 BCE in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info