79225
20
Verklein
Vergroot
Pagina terug
1/153
Pagina verder
English - 3
20 • F 016 L70 540• TMS • 29.01.09
Cut wood only. Don’t use chain saw for pur-
poses not intended – for example – Don’t use
chain saw for cutting plastic, masonry or non-
wood building materials. Use of the chain saw
for operations different then intended could result
in a hazardous situation.
Causes and Operator Prevention of Kickback:
Kickback may occur when the nose or tip of the
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and
back towards the operator.
Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards
the operator.
Either of these reactions may cause you to lose
control of the saw which could result in serious
personal injury. Do not rely exclusively upon the
safety devices built into your saw. As a chain saw
user, you should take several steps to keep your
cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given be-
low:
Maintain a firm grip, with thumbs and fingers
encircling the chain saw handles, with both
hands on the saw and position your body and
arm to allow you to resist kickback forces.
Kickback forces can be controlled by the opera-
tor, if proper precautions are taken. Do not let go
of the chain saw.
Do not over reach and do not cut above shoul-
der height. This helps prevent unintended tip
contact and enables better control of the chain
saw in unexpected situations.
Only use replacement bars and chains speci-
fied by the manufacturer. Incorrect replacement
bars and chains may cause chain breakage and/
or kickback.
Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead to in-
The chain saw is intended for sawing of trees, tree
trunks, branches, wooden beams, planks, etc. Cuts
can be sawed with or across the grain. This product
is not suitable for sawing mineral materials.
This manual gives instructions on the correct as-
sembly and safe use of your chain saw. It is impor-
tant that you read these instructions carefully.
Technical data
Chain saw
AKE 30 S AKE 35 S AKE 40 S
Part number (typ)
3 600 H34 4.. 3 600 H34 5.. 3 600 H34 6..
Rated power [W] 1800 1800 1800
Chain speed (no load) [m/s] 9 9 9
Chain bar length [cm] 30 35 40
Tool-less chain
tensioning (SDS)
Nose sprocket
Kickback Brake
Chain type
3/8" - 90 3/8" - 90 3/8" - 90
Drive link thickness [mm] 1.1 (0.043") 1.1 (0.043") 1.1 (0.043")
Amount of drive links
45 52 57
Oil reservoir capacity [ml] 200 200 200
Automatic oiler
Metal gripping teeth
Weight without mains cable.
approx. ** [kg] 3.9 4.0 4.1
Protection class
/ II / II / II
**measured with chain bar and chain
Note: Please observe the order number of your machine. The trade names of individual machines can vary.
Inrush currents cause short-time voltage drops. Under unfavourable power supply conditions, other equipment may be af-
fected. If the system impedance of the power supply is lower than 0.25 Ohm, disturbances are unlikely to occur.
Intended Use Introduction
F 016 L70 540 - GB Seite 3 Montag, 9. Februar 2009 3:37 15
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GKE 40 BCE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GKE 40 BCE in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info