680440
34
Verklein
Vergroot
Pagina terug
1/144
Pagina verder
4.5 Reversal limit
During operation of the gate in the CLOSE direction, the
system must distinguish between two possibilities: whether
the gate contacts the end stop (gate system stops) or an
obstruction (gate reverses direction). The limit range can be
adjusted as follows (see Figure9.4).
Setting the reversal limit:
1. Set DIL switch11 to ON.
The reversal limit can now be set step-by-step.
2. Briefly press print button P to decrease the reversal limit.
Briefly press print button T to increase the reversal limit.
During adjustment, the green LED will indicate the
following settings:
1× flashing
up to
Minimum reversal limit, the green LED
flashes once
10× flashing Maximum reversal limit, the green LED
flashes 10 times
3. Set DIL switch11 back to OFF to store the set reversal
limit.
4.6 Automatic timed closing
NOTE:
Automatic timed closing can only be activated if at least one
safety device has been connected. This is required according
to DINEN13241-1.
The hold-open phase can be set for operation with automatic
timed closing (see Figure 9.5).
Setting the hold-open phase:
1. Set DIL switch13 to ON.
The hold-open phase can now be set in increments.
2. Briefly press print button P to decrease the hold-open
phase.
Briefly press print button P to increase the hold-open
phase.
During adjustment, the green LED will indicate the
following settings:
1× flashing 30 second hold-open phase
2× flashing 60 second hold-open phase
3× flashing 90 second hold-open phase
4× flashing 120 second hold-open phase
5× flashing 180 second hold-open phase
3. Set DIL switch13 back to OFF to store the set hold-
open phase.
WARNING
Danger of injuries due to faulty safety equipment
In the event of a malfunction, there is a danger of injuries
due to faulty safety equipment.
After the learning runs, the person commissioning the
system must check the function(s) of the safety
equipment.
The system is ready for operation only after this.
5 DIL Switch Functions
The control is programmed via the DIL switches. Before initial
start-up, the DIL switches are in the factory settings, i.e. all
the switches are in the OFF position. Changes to the DIL
switch settings are only permissible under the following
conditions:
• The operator is at rest.
• The warning or hold-open phase is not active.
The DIL switches must be set as described below in
accordance with the national regulations, the desired safety
equipment and the on-site circumstances.
5.1 DIL switch1
Installation direction:
See Figure7.1
1 ON Gate closes to the right (as viewed from the
operator)
1 OFF
Gate closes to the left (as viewed from the
operator)
5.2 DIL switch2
Set-up mode:
See Figures 8.1a – c
The safety and protective devices are not active during set-up
mode.
2 ON • Teach-in gate travel
• Delete gate data
2 OFF
Normal mode
5.3 DIL switch3 / DIL switch4
SE1 safety device (opening):
See Figure9.6
The functions of the SE1 are set with DIL switch3 in
combination with DIL switch4.
3 ON Activation kit for closing edge safety device or
photocell with testing
3 OFF
• 8k2 resistance contact strip
• Photocell from another manufacturer
• No safety device (8k2 resistance between
terminals20 / 72, delivery status)
4 ON Brief, immediate reversing in the CLOSE direction
(for SKS)
4 OFF
Brief, delayed reversing in the CLOSE direction
(forphotocell)
34
C300 - C800 / Rev. 1.1 RE / 07.2014
ENGLISH
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Berner C500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Berner C500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 12,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info