471407
40
Verklein
Vergroot
Pagina terug
1/67
Pagina verder
38-EN
01GB07PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From the Commander
*
1
When you modify the “FRONT HIGH” speaker setting to [Full], a
message to confirm the change will be displayed. To set up at “Full
Range,” rotate the [Rotary encoder] to select “OK”, and then press
the [Rotary encoder]. Make sure the speaker being used for this
output is able to handle a full range source. Many tweeters can be
damaged when driven by a full range signal.
*
2
This item is enabled for setup only when 2 subwoofers are connected.
Rotate the [Rotary encoder] to select “Stereo” or “Mono”, and then
press the [Rotary encoder].
Stereo: Subwoofer stereo (L/R) output
Mono: Subwoofer monaural output
Speakers that cannot be turned off are disabled for setup. Refer to
Table 1 (Output System) in “System Configuration” (page 60).
When you connect just one subwoofer, turn off “Subwoofer2.
7-1
First time start-up:
The AUX Input System Select screen will be
automatically displayed. Continue to set, referring to
“Setting the AUX Input System (AUX Input Setup)”
(page 39).
7-2
Subsequent start-up:
The “Turn ACC Off” screen will be displayed. Turn the
ignition key to off and then on again. The settings
become effective.
If [ ] is pressed during setting, the unit returns to the previous
item.
If the speaker system is changed, all setup values except those for
AUX input will be restored to the initial setup values.
You can also set the speakers from “Setting the Speakers (Speaker
Setup)” (page 38).
You can also set the subwoofer output from “Setting the Subwoofer
Output (SW Channel)” (page 38).
After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 36).
Setting the Speakers (Speaker Setup)
Turn on the connected speakers.
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Output
Setup,” and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “Speaker
Setup,” and then press the [Rotary encoder].
The Speaker selection screen is displayed.
4
Rotate the [Rotary encoder] to select the speaker to
be set, and then press the [Rotary encoder].
Setting contents: Front High/Front Mid/Front Low/Rear/
Center/Subwoofer (1, 2)
Speakers to be set vary depending on the system set in “Setting the
Speaker System (System Select)” (page 37).
Speakers that cannot be turned off are disabled for setup. Refer to
Table 1 (Output System) in “System Configuration” (page 60).
5
Rotate the [Rotary encoder] to select “ON” or “OFF,
etc., and then press the [Rotary encoder].
Repeat the steps until all the speakers are set.
Front High*: OFF/Tweeter/Full
Front Low: OFF/ON
Rear: OFF/ON
Center: OFF/ON
Subwoofer(1, 2): OFF/ON
* When you modify the “Front High” speaker setting to [Full], a
message to confirm the change will be displayed. To set up at “Full
Range,” rotate the [Rotary encoder] to select “OK”, and then press
the [Rotary encoder]. Make sure the speaker being used for this
output is able to handle a full range source. Many tweeters can be
damaged when driven by a full range signal.
When you connect just one subwoofer, turn off “Subwoofer2.
6
To set up other speakers, press [ ] and repeat
Steps 4 and 5.
7
When the setting is complete, press and hold [ ]
for at least 2 seconds.
If [ ] is pressed during setting, the unit returns to the previous
item.
When the speaker setting is changed while ImprintEQ/RoadEQ is on,
ImprintEQ/RoadEQ will be turned off after a confirmation message
is displayed.
After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 36).
Setting the Subwoofer Output (SW
Channel)
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type. (Initial Setting: “Mono”)
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Output
Setup,” and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “SW Channel,
and then press the [Rotary encoder].
The Subwoofer Channel selection screen is displayed.
4
Rotate the [Rotary encoder] to select “Mono” or
“Stereo,” and then press the [Rotary encoder].
Mono: Subwoofer monaural output
Stereo: Subwoofer stereo (L/R) output
01GB00PXAH800.book Page 38 Tuesday, February 8, 2011 9:04 PM
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alpine RUX-C800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alpine RUX-C800 in de taal/talen: Engels als bijlage per email.

De handleiding is 11,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info