T
1. Connect the power adaptor to the camera and slide the
ON/OFF switch at the rear to the ON position.
2. Open the menu on the parent unit by pressing the but-
ton and use the and buttons to select the option .
3. Use the and buttons to select the option and
press the button.
4. Use the and buttons to select the next available free
camera number and press the button.
5. Press and hold the P
new camera until the green ON/OFF indicator starts ash-
ing after several seconds to indicate that the camera is
now searching for the monitor
6. After several seconds the images of the new camera will
appear in the display of the parent unit.
Repeat these instructions if the registration process doesn’t
succeed the rst time.
T
1. Open the menu on the parent unit by pressing the but-
ton and use the and buttons to select the option .
2. Use the and buttons to select the option and
press the button.
3. Use and to select the desired camera number and
press the button.
4. After several seconds the parent unit will show the images
of the selected camera.
In the right upper corner of the display the number is shown of
the camera that is currently viewed.
Camera SCAN:
At the above instruction 2, select the option and press
the button to enable the SCAN mode. The images and
sound of all registered cameras are now played via the parent
unit, in order and 10 seconds for each camera.
Attention: The unit does NOT automatically switch to a
camera where sound is being detected.
TIPS AND WARNINGS
GENERAL:
• Thoroughly read the user
indications.
• Never place the baby unit or parent unit in wet or humid
room or environment.
• Ensure adequate heat dissipation; never cover the parent
unit, the baby unit and/or the power adapter(s) and never
place them directly next to a heat source.
• Only use the supplied adapter(s); connecting a different
type of adapter will damage the electronics.
• Make sure the adapter cables are free of any damage and
ensure nobody can trip or fall because of these cables.
• Never dismantle the parent unit, the baby unit and/or the
power adapter(s); only qualified personnel is authorized
to do so.
BA
The battery starts charging as soon as you connect the parent
unit to the power adaptor and insert this adaptor into a 230V
wall socket.
• Y
charging circuit for the battery is controlled electronically
and there’s no risk of overcharging.
• However
time (>2 months), we recommend you to remove the
adaptor from the wall socket and take out the battery from
the parent unit. When using the set again, rst properly
charge the battery
INST
• Only connect or disconnect the power adapter to/from
the baby unit or parent unit when the power adapter is
removed from the wall socket.
• Never install the DVM-250 during thunder storms.
• Never touch any non-isolated adapter cables, unless the
adapters are removed from the wall socket.
INTERFERENCE-FREE:
• This baby display monitor is digitally coded. This means
you will never receive signals from other devices, nor can
the signal from your baby unit(s) be received by e.g. your
neighbors.
• In case the baby unit(s) or parent unit is placed in or in the
close vicinity of electromagnetic fields, the signal (images
or sound) can be slightly affected. If this happens, try
a different location for the baby unit(s) or parent unit or
move, if possible, the source of the interference.
EA
• Eavesdropping/wiretapping of the signals from this baby
video monitor is nearly impossible. Not only must one be
within range of the baby video monitor
some very costly equipment.
RANGE:
• The baby display monitor has a range of up to 300 meters
in an open field and up to 50 meters indoors; this range
depends on local circumstances.
• When the units get out of range of each other, the ‘out of
range’
X
) will appear and every minute several
alert beep tones are emitted.
and parent unit are back within range of each other
warning will stop.
DELA
• The baby unit transmits the images and sound to the
parent unit in digital blocks. The parent unit converts
these signals back to a recognizable image and a
comprehensible sound. Therefore, there is a small delay
between the moment of movement and making sounds
and the display and sounds of the parent unit.
• Besides that, the sounds and images on the parent unit
are not exactly simultaneous.
MAINTENANCE:
• Only clean the baby monitor with a moist cloth; never
use chemical cleaners. Before any cleaning, you must
disconnect the adapters.
ENVIRONMENT AND
• The packaging of this baby video monitor can be
discarded as waste paper
save this packaging so you can adequately protect the
devices for transportation.
• Faulty or exhausted batteries or battery packs
should be taken to your local depot for small
chemical waste or to dedicated battery collection
points. Never dispose of batteries or battery packs
as normal household waste.
• In case the baby video monitor is being replaced, please
return it to your supplier; they will guarantee environment-
friendly processing.
PROBLEMS:
• no image, no sound:
are the parent unit and baby unit switched off? (battery
charged, battery full?)
is the parent unit within range of the baby unit?
is the image and sound are not disabled because no
sound is being detected? (VOX)
is the volume at the parent unit set to 0 (off)?
• If the above is all in order, remove the adapters from the
wall sockets, take the rechargeable battery out of the
parent unit, wait at least one minute and then reconnect
everything. Now
on.
• If you still receive no images or sound, please contact
the customer service of
641
internet www
SPECIFICA
Range: up to 50 meters indoors
up to 300 meters outdoors
Parent unit power: 3.7V Li-Ion battery pack,
1440mAh
5VDC 1000mA
model: ZD5C050100EUDW
Baby unit power: 5VDC 600mA
(incl.)
model: ZD5C050100EUDW
Frequency: 2400MHz - 2483.5MHz
Modulation: GFSK, FHSS
RF output: 18+/-1dBm
RF sensitivity: <= 85dBm
Display: 5.0” color LCD display
480x272 pixels
Battery charging duration: +/- 4 hours (*)
Battery operation duration: 6~8 hours (*)
Operation temperature: 0°C - 40°C
Operation humidity: 40%~90% RH
Storage temperature: -10°C - 50°C
Accuracy: ± 2°C (at 25°C)
Monitor suitable for: 4 cameras
*: the times mentioned above are references only and depend
on the usage, condition and quality of the batteries.
WARRANTY
For the
from the date of purchase. During this period, we guarantee
the free repair of defects caused by material and workmanship
errors.
importer
HOW T
user
please contact the supplier of this baby video monitor or
contact customer service of
alecto.nl
THE W
of improper use, incorrect connections, leaking and/or
incorrectly installed batteries, use of unoriginal parts or
accessories, negligence and in case of defects caused by
moisture, fire, flooding, lightning and natural disasters. In case
of unauthorised modifications and/or repairs performed by
third parties. In case of incorrect transportation of the device
without adequate packaging and when the device is not
accompanied by this warranty card and proof of purchase.
The warranty does not cover connecting cables, plugs
and batteries.
consequential damages, is excluded.
MENU-OPERA
Briey press the button to open the menu. Now use the
direction buttons or to select one of the following functions:
Brightness:
Use and to select the desired brightness and press to
save your setting and leave the menu.
Keep in mind that more power is used at a high inten-
sity level compared to a low display intensity level. We
recommend a lower intensity level for mobile use, i.e. when
using the unit on battery power
level when using the adaptor
Lullabies:
Use and to select the desired lullaby (choose 1-4) or se-
lect the ocean sounds (5). When selecting all 4 lullabies
are played in order
Playback starts immediately and stops automatically after
15 minutes or you may select the option
OFF
to stop playback
beforehand. Press to save your setting and leave the menu.
Keep in mind that the sound of the lullaby is returned to
the parent unit via the microphone of the baby unit. In
this case, you may want to set the sound of the parent unit to
level 0 (= sound off).
Multi-camera:
Introduction:
Y
on the DVM-250 parent. When multiple baby units are regis-
tered on the parent unit, you can manually switch to another
baby unit or have the images of all registered baby units
automatically shown one after the other
Separate cameras are available via the
ment via www
T
Choose the options
HIGH
and
LOW
to set the maximum and
minimum temperature for the baby room:
Select
HIGH
or
LOW
, press the button and use the and
buttons to set the maximum or minimum value; press the
button (or the button) to save your setting and press the
button to leave the menu.
Alarm on/off:
Choose the options
ON
and
OFF
to enable or disable the
temperature alert. Select the desired option, press the
but-
ton to save your setting and press the
button to leave the
menu. When the alarm is enabled, the
symbol illuminates
in the upper part of the screen.
How the temperature alert functions:
As soon as the minimum or maximum limit is exceeded, the
temperature display and the symbol start ashing and
every 10 seconds several warning beep tones are emitted.
As soon as the temperature returns to within the set limits, the
alert tones will stop. Y
alert to stop the beep tones beforehand.
VOX:
This menu allows you to set how loud the baby must be crying
before the display and sound must switch on when you’ve
enabled the VOX function of the baby monitor:
• option (upper option in the screen):
high sensitivity
detected
• option (middle option in the screen):
average sensitivity
• option (lower option in the screen):
low sensitivity
Press to save your setting and leave the menu.
When the display and sound turn off during use while
the baby is still making sounds, set a higher sensitivity
level or disable the VOX function to watch and listen continu-
ously
T
Cameras that are defect or no longer being used must be
removed from the system of the parent unit as follows:
1. Open the menu on the parent unit by pressing the but-
ton and use the and buttons to select the option .
2. Use the and buttons to select the option and
press the button.
3. Use and select the number of the camera that must
be removed and press the button.
4. The parent unit will emit a tone and the selected camera is
de-registered.
Zoom:
This menu allows you to enlarge the display (move somewhat
closer).
Select for an enlarged view and select for a normal
view
When the zoom function is enabled, the icon appears in
the upper part of the display
Press to save your setting and leave the menu.
T
In the upper right corner of the parent unit, the temperature is
shown of the room where the baby unit is located.
Display in °C or in °F:
Choose the option
°C
to set the temperature display to de-
grees Celsius or select the option
°F
to have the tempera-
ture shown in degrees Fahrenheit. Select the desired option
and press the to save your setting.
Display calibration (correcting):
Choose the option to correct the temperature display:
select this option, press the button and use the and
buttons to set the correct temperature of the baby room. Press
the button to save your setting and press the button to
leave the menu.
V1.0
Service Help
WWW
SERVICE@ALECT
Hesdo, Australiëlaan
5232 BB, ‘s-Hertogenbosch
The Netherlands
WWW
SERVICE@ALECT
Hesdo,
‘s-Hertogenbosch,
The Netherlands
