668919
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
INSTALLATION
BABY UNIT: (CAMERA)
Power:
1. Connect one of the supplied 5V power adaptors to the 5V
DC input of the baby unit.
2. Insert the adapter into a 230V wall socket.
Only use the supplied power adaptor.
Make sure that the baby can’t
touch the wire of the baby unit.
Place the baby unit at least
1-1.5 meters away from the baby
and bundle excess cable lengths
using tape or cable-ties specically designed for this purpose.
Table model or wall model:
You may place the baby unit loose on a table, cabinet or desk
or suspend it from a wall.
For wall mounting:
Drill two holes in the wall, next to each other and at a distance
from 2.1cm, then insert plugs and screws. Leave the head of
the screw protrude for several millimeters.
Suspend the baby unit by sliding the recesses in the camera
support over the screws in the wall and then pressing the
baby unit somewhat downward. Finally, neatly hide the adap-
tor cable using cable-ties.
Tips for placement:
For use as a baby monitor: place the baby unit at least
1-1.5 meters away from your baby and make sure to
safely tuck away the adapter cable.
The temperature protrudes from the rear of the baby unit.
Make sure this sensor hangs freely, unexposed to direct
sunlight and avoid heat from e.g. light bulbs.
parent unit switched off and power adaptor connected:
orange light while the battery is being charged
green light remains lit when the battery is fully charged
10. VOX indicator, illuminates when the VOX function is en-
abled
11. Antenna
12. Sound indicators, ashing when the baby is crying
13. Volume +/- buttons
14-17. , , and buttons
18. Built-in speaker (rear)
19. Foldable table support (rear)
BABY UNIT:
20. Antenna
21. Light sensor, for enabling
and disabling the night
view LED’s
22. Camera lens
23. This area contains the
infra-red LED’s for the
night view lighting (not vis-
ible to the naked eye)
24. Built-in microphone
25. Coupling ball, to properly
and accurately orientate
the baby unit
26. Built-in speaker
27. Temperature sensor
28. Power adaptor input
29. ‘PAIRING’ button, to regis-
ter (or re-register) the baby
unit on the parent unit
30. On/off switch with indicator
SYMBOLS IN THE DISPLAY
While using the parent unit, the following symbols may appear
in the display:
In the upper left corner, the signal strength is indicated:
strong reception
good reception
average reception
and poor reception
no reception
When talking to the baby, the talk-back symbol on the right
side of the antenna symbol will illuminate.
CAM1
In the upper right corner, the camera you’re currently
watching is indicated. When multiple cameras are connected
to the parent unit and you’ve enabled the scan function (to
automatically switch to the next camera screen every 10 sec-
onds), also the symbol will appear.
Next to the camera indication, the battery capacity is shown:
battery full
battery 3/4 full
battery 2/4 full
battery 1/4 full
the outline is red and ashing: the battery is nearly ex-
hausted and the parent unit may switch off at any moment
no battery inserted or the battery is not connected. While
charging, the battery symbol keeps scrolling until the battery is
fully charged.
While adjusting the volume, the current volume level
is shown in the right side of the display. When the
volume level is set to 0 (sound off), the ‘no sound’
icon will appear here.
When the volume is turned off, the symbol appears in the
upper part of the display to remind you that you’ve switched
off the sound.
Press the button to open the
menu. You’ll nd a description
of these functions further in this manual.
illuminates when the temperature alert is enabled. This
symbol starts ashing when the set limit is exceeded.
USE
The functions ‘Brightness’, ‘Lullabies’, ‘Multi-camera’,
‘Zoom’, Temperature display and alert’ and ‘VOX’
(screen and sound switch off automatically when the baby is
sleeping) are described on the other side of this user’s manual
underneath the header ‘MENU-OPERATED FUNCTIONS’.
BABY UNIT:
Switching on/off:
Slide the ON/OFF switch at the rear to the ON position to turn
on and slide to the OFF position to turn off. The green light
underneath the ON/OFF switch illuminates several seconds
after you’ve switched on the unit.
Automatic night vision:
The baby unit is provided with built-in infra-red LEDs; these
LEDs will switch on automatically when the baby room turns
dark and will switch of again when it becomes light.
The LEDs can illuminate objects up to a distance of
approximately 2 meters.
When it’s dark, that is when the night vision LEDs
are switched on, the images on the parent unit will be
displayed in black and white.
Attention: infra-red light cannot be perceived by the
human eye; that means you cannot tell whether the
infra-red LEDs are switched on with the naked eye.
PARENT UNIT:
Switching on/off:
press and hold for 2 seconds to turn off
Volume:
Use the + and - buttons to set the loudness of the sounds
from the baby room that you hear through the speaker of the
parent unit.
While adjusting, the volume level will be indicated on the display.
Talk-back function:
When the screen is enabled, press the button to talk to
your baby. Press and hold the button for as long as you’re
talking and release the button to listen.
Sound indicators:
In the middle of the upper part of the display you’ll nd 4
sound indicators indicating whether the baby is crying by
ashing. This allows you to watch over your baby when the
sound is set to a low level or is turned off, or when the baby
monitor is placed a bit further away in the room.
Automatic on/off function: (VOX)
When the baby is sleeping quietly or when the baby unit is not
picking up any sounds, you may have the display and sound
of the parent unit switch off automatically and back on again
as soon as the baby starts crying.
The sensitivity of the automatic on/off function can be adjusted
(see chapter MENU further in this user’s manual). Use the
VOX push-button to enable or disable this function; the VOX
indicator shows whether this function is enabled or disabled:
light off = VOX function off
(the images and sound are
transmitted continuously)
light on = VOX function on
(display and sound off while the
baby is sleeping)
To check in the meantime:
By briey pressing any button you may enable the display and
sound again for a short time to watch and listen to the baby.
After several seconds, the display and sound are turned off
again.
Battery weak (empty) notication:
When in use, the battery symbol in the upper right corner of
the display shows the battery capacity.
As soon as the battery capacity falls below 25%, the red
power LED will illuminate to inform you of this. It’s now recom-
mended to connect the adaptor to recharge the battery.
When the battery capacity further decreases to nearly empty,
this red battery symbol starts ashing. Also the power indica-
tor starts ashing in red and every 30 seconds several alert
tones are emitted for 10 to 15 minutes long. Now immediately
connect the adaptor otherwise the parent unit will switch itself
off within this time period.
USER’S MANUAL
DVM-250
INTRODUCTION
The Alecto DVM-250 is a wireless baby monitor observa-
tion system, suitable for private use indoors.
You can either watch and listen continuously or you can
have the baby monitor switch on.
The Alecto DVM-250 meets all essential requirements
and other provisions as described in the European Direc-
tive 1999/5/EC.
The declaration of conformity is
available on the website www.
alecto.nl
Use of this equipment is allowed in all countries of the
EU. In France, Italy, Russia and Ukraine, only indoor use
is allowed.
ATTENTION
Before you start using the set, please remove any protective
foil from the parent unit and baby unit.
About this users manual:
This symbol represents a warning. To ensure safe use,
always adhere to the instructions described in this
documentation.
This symbol is followed by a user’s tip.
Always check the Alecto website for the most recent version of
this user’s manual.
FUNCTION OVERVIEW
PARENT UNIT:
1. Battery compartment (rear)
2. Power adaptor input
3. VOX on/off button
4. ENTER button for menu settings
5. MENU button
6. Talk-back button
7. Power on/off button
8. Built-in microphone
9. Power indicator:
parent unit switched on, power adaptor not connected:
green light during normal use
red light when the battery capacity is low
ashing red light when the parent unit may switch off at
any moment due to a low battery capacity
parent unit switched on and power adaptor connected:
ashing green light while the battery is being charged
green light remains lit when the battery is fully charged
For optimal range, it is advisable to set up the baby unit as
high as possible, free from large metal surfaces.
The baby unit is not waterproof and therefore suit-able
for indoor use only.
PARENT UNIT: (MONITOR)
Battery:
1. Open the battery compartment by sliding and clicking off
the battery cover at the rear.
2. Connect the battery plug in the battery compartment ac-
cording to the gure below and install the battery.
3. Click the battery cover back onto the parent unit.
Never connect the plug or install the battery by force.
Only install the supplied rechargeable Li-ion battery (3.7V,
1440mAh).
Power adapter:
1. Connect the other 5V power adapter on the left side of the
parent unit.
2. Insert the adapter into a 230V wall socket.
The battery starts charging as soon as you connect the power
adaptor. When using it for the rst time, please charge the
battery for at least 15 hours, even when the indicator shows a
fully charged battery.
Only use the supplied power adaptor.
General:
Fold out the support at the rear to place the parent unit onto a
table or cabinet.
Keep the antenna of the parent unit in an upright position for
optimal range.
The parent unit is not water-proof, hence is only suitable
for indoor use.
20
22
23
25
24
21
28
29
30
27
26
6
5
4
7
3
14
15
16
13
17
VOX
8 9 10 11 12
2
18
1
19
1-1.5m
VOX
VOX indicator
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alecto DVM-250 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alecto DVM-250 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Alecto DVM-250

Alecto DVM-250 Gebruiksaanwijzing - Nederlands - 2 pagina's

Alecto DVM-250 Gebruiksaanwijzing - Deutsch - 2 pagina's

Alecto DVM-250 Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info