782361
78
Verklein
Vergroot
Pagina terug
1/136
Pagina verder
72
SCOOPY+ S - User Manual
AoIP settings
These settings apply to any connection using the IP protocol, hence all Ethernet or mobile IP interfaces
are concerned. They can be found in the sub-menu Setup / Network / AoIP Parameters, and details
about these settings are described in 4.4.1, "AoIP Parameters" section.
The most common and convenient connection method is by using the SIP protocol: select "SIP" as first
parameter (Default protocol).
If a SIP server is used, you should register the SCOOPY+ S on this server. Use the sub-menu to enter the
SIP account data and activate the SIP registration. Check that the codec is properly registered thanks to
the indicator on the base screen ("S" sign at the middle of the top line), otherwise via the sub-menu
Tools / About, SIP Status information.
Besides, for links over the Internet, most often the link passes through a NAT router which "hides" to the
codec the characteristics of the public access: public IP address and RTP ports actually used. This can
make the SIP transactions fail, or get a non-optimal route through the network. To avoid this, a STUN
server is often used; the corresponding settings are also found in the AoIP Parameters sub-menu.
Check that the public address discovery has succeeded: Tools / About sub-menu: Public IP information
(its mere presence shows the discovery has succeeded). The type of NAT detected by the Scoopy+ S is also
shown in this sub-menu (NAT Type).
If you wish to use the "Direct RTP" mode instead of SIP for outgoing calls, select "RTP Direct" for the first
parameter (Default protocol). This mode involves in fact no signalling protocol such as SIP, but its
operation is somewhat similar: a codec "calls" another, in fact initiates a link by directly sending a
stream to the other end. The "receiver" of the call should be configured for accepting this incoming
"call" and sending its own stream back to the initiator of the link.
Ethernet interface
Use an RJ45 cable to connect the SCOOPY+ S to a router or switch. A couple of LEDs on the Ethernet
socket (back panel, see 3.2.2) indicate the status and activity of the Ethernet link.
It may be necessary to configure the network interface depending on the local installation, especially
when it does not include a DHCP server. The Ethernet interface settings are reachable via the sub-menu
Setup / Network / Ethernet Parameters.
The various parameters are described in 4.4.1, "Ethernet Parameters" section.
In most cases, you can use the following settings:
Mode: "DHCP"
Link Mode: "Auto-Negotiation"
Network Quality: "Middle"
78

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aeta Scoopy plus S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aeta Scoopy plus S in de taal/talen: Engels als bijlage per email.

De handleiding is 5.56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info