540053
23
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
23
PG-005_v01
The earthing wire must be connected to the
terminal marked with the symbol
. The
electrical installation supplying the hob should
be protected with a properly selected safety
device and, in addition, it should be equipped
with a suitable switch enabling the current to
be cut off in an emergency situation.
Make sure that the mains voltage corresponds to the
voltage on the rating label located on the appliance
casing.
The hob is designed to be connected to a 230 V 50 Hz
AC electricity supply and should be connected to a mains
socket equipped with a properly connected earthing
contact.
If the electrical installation is damaged, connecting the
hob to the socket without an earthing contact will create
the risk of electric shock.
The installer is obliged to ll in the warranty
card, which is the basis for warranty claims.
Changing the nozzles for di erent
type of gas (Fig. B)
Nozzles can be changed only by a certi ed
installation technician.
The gas hob is equipped with nozzles adapted for use with
2E (G20) gas.
Type of gas and gas pressure, as well as thermal power and
designation of nozzles for particular burners are shown in the
table below:
BURNER GAS PRESSURE NOZZLE
MARKING
THERMAL
CAPACITY
LARGE
2E (G20)
3B/P (G30)
20 mbar
37 mbar
1.18
0.72
2500 W
MEDIUM
2E (G20)
3B/P (G30)
20 mbar
37 mbar
0.92
0.58
1500 W
SMALL
2E (G20)
3B/P (G30)
20 mbar
37 mbar
0.75
0.49
1000 W
1
Remove the burner cap and crown.
2
Unscrew the nozzle using a special spanner.
3
Replace the nozzle with that for a new type of gas
according to the table.
After changing the nozzles, adjust the burners (see
“FLAME ADJUSTMENT”).
After changing the nozzles af x an appropriate
label showing the new type of gas at the hob
connecting pipe.
Technical Parameters
The technical parameters are indicated on the rating label.
The hob is equipped with a threaded connecting pipe
G1/2’’ used for connecting to the gas mains. In the case of
connecting the hob to liquid gas (propane-butane) tanks the
tting for 8 x 1 mm hose must rst be screwed onto the
connecting pipe.
The gas hob is a class 1 appliance equipped with a power
cord with an earthing wire. It must be connected to the mains
socket equipped with an earthed pin.
The appliance satis es the requirements of relevant
standards.
The appliance complies with the following directives:
Appliances burning gaseous fuels (GAD) – 90/396/EEC,
93/68/EEC.
Low Voltage Directive (LVD) – 2006/95/EC.
Electromagnetic Compatibility (EMC) – 2004/108/EC.
The product is marked with the CE symbol on the rating label.
Appliance elements (Fig. D)
1
Large burner Ø 100 mm 2.5 kW
2
Medium burner Ø 75 mm 1.5 kW
3
Small burner Ø 55 mm 1.0 kW
4
Burner knobs with ignition switch
5
Pan support
6
Burner cap
7
Burner crown
8
Burner base
9
Ignitor
10
Flame failure safety device
Flame adjustment (Fig. C)
Flame adjustment should be performed by
a certi ed installation technician.
1
Light the burner and set it to the minimum ame .
2
Remove the knob from the shaft.
3
Use a special screwdriver and adjust the ame by turning
the screw inside the shaft. As a result you will obtain a small,
uniform ame around the burner.
In the case of 3B/P (G30) gas the screw must be fully
screwed in (clockwise).
4
Replace the knob
Make sure that when the knob is turned rapidly from
maximum
to minimum , the ame does not go out.
5
Turn off the burner by turning the knob to position .
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zelmer ZPG6004SZ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zelmer ZPG6004SZ in de taal/talen: Engels, Pools als bijlage per email.

De handleiding is 0,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info