Handleiding Zelmer Tiny VC1400.0 SK (pagina 58 van 62) (Engels, Pools)

539694

Verklein

Vergroot

Pagina terug

1/62

Pagina verder

64 VC1400-001_v02

Special accessories

The following special accessories may be purchased in retail

outlets:

Parquet brush “BNB” (22)

Is used to clean and polish hard, scratch sensitive surfaces

such as wooden oors, oor panels, parquet, marble, tiles,

etc.

Delicate and soft natural bristles ensure maximum vacuum

effectiveness and protects against scratching the cleaned

surface.

Zelmer turbobrush (23)

May be used with all types of ZELMER vacuum cleaners.

Is used for an effective vacuuming of carpets and tted

carpets. While using the turbobrush follow the instruction

manual.

The use of the turbobrush decidedly increases the

effectiveness of removing brous dirt such as: animal hair,

hair, threads etc. It is practically useful in households with

pets (cats, dogs), where removing the animal hair from the

carpets and oorings is very onerous.

After-work procedures, cleaning and

maintenance

Press the on/off button to stop the vacuum cleaner.

Remove the plug of the cord from the socket.

Wind the cord by pressing the cord winder button (8).

Hold the cord when doing it to avoid tangling the cord up or

letting the plug hit the vacuum cleaner.

Disconnect the telescopic suction pipe from the nozzle or

brush.

Disconnect the suction tube from the hose. In order

to remove the telescopic tube from the hose handle,

simultaneously press the lock A and pull the tube in the

direction indicated by the arrow.

Turn the end of the suction hose counter-clockwise, and

remove the end of the hose from the inlet of the vacuum

cleaner.

The vacuum cleaner may be store in a horizontal

position. In order to do this place the hook of the nozzle

brush into the fastening of the nozzle brush situated at the

back of the vacuum cleaner, near the entrance of the power

cord. The hose may stay attached to the vacuum cleaner as

long as it is not bent too much during storage.

If necessary, clean the casing and the chamber of the

vacuum cleaner with a damp cloth (it may be damped in

dishwashing liquid), dry it off, and wipe it dry.

Donotuseanyscrubbingagentsorsolvents.

Place the new/rinsed HEPA H12 basic lter (14) in the

previously determined spot in the dust container.

Situate the protective casing of the HEPA H12 basic lter

in the chamber of the container, in the previously determined

spot. Pay attention that the protrusions situated on the ange

of the container are inserted in the sockets of the body of the

container.

Turn the protective casing of the HEPA H12 basic lter

in the direction given on the symbol „ ” (it is situated along

with an arrow on the protective casing of the HEPA H12 basic

lter).

Place the cover of the CYKLON dust container on the

container in such a way that the fastening situated in the

front part of the cover is inserted into the projection of the

container. Press the back part of the cover in such a way that

the fastenings are shut tight on the body of the container.

Situate the CYKLON dust container with the installed

HEPA H12 basic lter (14) in the chamber of the vacuum

cleaner. Close the upper cover of the vacuum cleaner by

pressing it, until you hear a characteristic “click.”

 WeadviseyoutoreplacetheHEPAH12basic

lter (14) with a new one every6 months of

use.

 Always replace a damaged HEPA H12 basic

lterwithabrandnew,originalone.

OUTLET MICROFILTER

In order to replace the outlet microlter (13) press the

blocking mechanism on the cover of the outlet lter, and then

remove the cover of outlet lter out of the vacuum cleaner.

Remove the outlet lter from the cover.

If the outlet microlter (13) is dirty, you may replace it with

a new one, clean it or rinse it with running water. Before

reinstalling the lter, make sure it is dry.

 Forsafetyreasons,itisunacceptabletoinstall

awetordamagedoutletmicrolter.

Situate the new/rinsed lter carefully onto the

4 fastenings of the outlet lter cover with the foam sides

towards themselves.

Place the lter cover in such a way that the two

protrusions situated in the lower part of the cover are

inserted into the holes in the body of the vacuum cleaner,

and then press the lter cover to snap the fastening in the

body shut. A characteristic “click” signalizes the lter cover

has been properly installed.

 Always replace a damaged microlter with

abrandnew,originalone.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Zelmer Tiny VC1400.0 SK Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info