633006
1
Verklein
Vergroot
Pagina terug
1/1
Pagina verder
NOTICES AND WARNINGS
OVERVIEW
1 GB203
2 GB203 LED Status Indicator
3 Main LED Status Indicator
4 Power Switch
5 MK58
6 Proportional Control Rate Slider
7 USB Connector/Charging Port
8 Audio/Earphone Jack
9 Take Still Photo Button (disabled)
10 Start/Stop Motors Button
11 Rudder/Yaw Control (for Mode 2 and Mode 1)
12 Throttle/Altitude Control (for Mode 2)
Elevator/Pitch Control (for Mode 1)
13 5.8GHz Antenna (located inside the case)
14 Status Indicators (for ST10+ battery, 5.8GHz WiFi and GPS)
15 2.4GHz Antenna (located inside the handle)
16 Start/Stop Video Recording Button (disabled)
17 Flight Mode Selection Switch
18 Aileron/Roll Control (Mode 2 and Mode 1)
19 Elevator/Pitch Control (Mode 2)
Throttle/Altitude Control (Mode 1)
20 Power Switch
21 Volume and Navigation Touch-Activated
Buttons Volume Down/VolumeUp/Menu/Home/Back)
22 Gimbal Pitch Angle/Position Control Slider
23 SD Card Slot (located under the battery)
6
7
8
9
10
11
12
13 14 15
16
17
18
19
20
21
22
23
TYPHOON G V1.0
Power the SC3500-3 charger from a 100-240V AC
outlet using the AC adapter/power supply, or from a
12V DC accessory socket/cigaree lighter
receptacle in a vehicle using the included adapter.
A green blinking LED indicates the charger is
powered on and ready to charge, and a red blinking
LED indicates the baery is charging. It will take
approximately 2 hours to charge a fully discharged
(not over-discharged) baery.
WARNING: All instrucons and warnings must be
followed exactly to prevent property damage and/or
serious injury as the mishandling of Li-ion/LiPo
baeries can result in fire.
IMPORTANT NOTE:
This Quick Start Guide is NOT intended to replace
the content included in the instrucon manual. You
should read the instrucon manual completely
before proceeding.
NOTICE:
Please find a SD Card in the asseccory box.
There are tutorial video, electronic user manual and
show case in the SD Card.
NOTE: If the door does not close, the baery is not
inserted far enough to engage the connector
properly.
6. PLACEMENT BEFORE TAKEOFF
10000 ² (930m²)
PILOT LOCATION
TAKEOFF ZONE
26  (8m)
100˚
WARNING: Always operate TYPHOON in open
areas (approximately 10000 square feet/930 square
meters or more) that are free from people, vehicles,
trees and other obstrucons. Never fly near or
above crowds, airports or buildings.
5. INSTALLING THE GOPRO©
Insert the GoPro© camera into the camera frame on
the GB203, then thread the camera to secure
posion with the retaining screw. Do not over-ghten.
Step back approximately 26 feet (8 meters) behind
TYPHOON.
7. POWERING ON/OFF
NOTE: ALWAYS turn the ST10+ on and allow it to
boot up BEFORE turning TYPHOON on (and
ALWAYS turn TYPHOON off BEFORE turning off
the ST10+).
Place TYPHOON on a level and stable surface then
slide the switch to the ‘ON’ posion. DO NOT TOUCH
OR MOVE TYPHOON UNTIL THE INITIALIZATION
10. STARTING/STOPPING THE MOTORS
11. FLIGHT CONTROLS
FLYING
Take your me learning how TYPHOON responds to
various control inputs while flying. In Smart Mode
TYPHOON will always move in the direcon the
right-hand control sck is pushed relave to the pilot
and no maer which way the front/nose is pointed.
In Angle (Pilot) Mode TYPHOON will move in the
direcon the control sck is pushed relave to the
front/nose of the aircra (and the ‘angle’ of
movement is determined by how far you push the
sck away from the center posion). And please see
the corresponding secons of this instrucon
manual for more informaon on Smart Mode and
Angle (Pilot) Mode.
IMPORTANT NOTE: If at any me during flight you
feel like TYPHOON is driing out of/beyond your
control, simply release both control scks.
TYPHOON will automacally self-level and will even
hold its posion (with a suitable GPS signal/lock)
when both control scks are centered. You can also
acvate Home Mode so TYPHOON automacally
land within 13-26  (4-8m) of the pilot.
LANDING
There are two ways to land TYPHOON:
1) Posion TYPHOON above the area where you
would like to land. Slowly lower the le-hand sck to
below the center posion. TYPHOON will descend
slowly and land. Aer TYPHOON lands, press and
hold the red START/STOP buon unl the motor stop.
2) Acvate Home Mode and TYPHOON will automa-
cally fly itself back to the home point and will land
within a 10 foot (3 meter) diameter circle around it.
WARNING: Always land as soon as possible aer the
first low level voltage baery warning, or land
immediately aer the second level low voltage
baery warning (as indicated by the vibraons and
audible alerts from the ST10+, and by the Below
Motor LED Status Indicators flashing rapidly). And if
at any me the Aircra Baery Voltage shown on
the screen is below 10.7V, land TYPHOON
immediately.
AFTER LANDING
ALWAYS turn off TYPHOON BEFORE turning off
the ST10+. Then remove the baery from
TYPHOON and allow it to cool to ambient/room
temperature before recharging.
Step back approximately 26 feet (8 meters) behind
TYPHOON. Press and hold the red START/STOP
buon for about 3 seconds to start, and about 2
seconds to stop the motors.
To takeoff, slowly raise the le-hand sck to slightly
above the center posion. TYPHOON will takeoff
and climb slowly (or raise the sck further unl it
does). Allow the sck to return to the center posion
when TYPHOON reaches the desired altude.
12. CONTROL RATE SLIDER
Set the overall climb/descend and direconal control
rates. Use the turtle posion for the lowest control
rates (best for first-me pilots and when flying
between 5000 feet and 8000 feet Above Mean Sea
Level). Use the rabbit posion for the highest control
rates (best for experienced pilots and only when
flying below 5000 feet AMSL.
13. SELECTING A FLIGHT MODE
TYPHOON is programmed with three (3) flight
modes that can be selected via the Flight Mode
Selecon Switch located just above the right-hand
control sck.
SMART MODE
When the Flight Mode Selecon Switch is the top
posion TYPHOON will be in Smart Mode. Although
we recommend learning to fly TYPHOON in Angle
(Pilot) Mode as soon as possible, Smart Mode is
typically the best mode for first-me pilots to fly in
and also features ‘Follow Me’.
In Smart Mode TYPHOON will always move in the
direcon the right-hand control sck is pushed
relave to the pilot and no maer which way the
front/nose is pointed. So if you push the sck to the
le TYPHOON will always move to the le,
regardless of the direcon the nose is poinng and
even if it’s spinning. This mode can also be helpful for
pilots that lose orientaon while flying in Angle
(Pilot) Mode.
1) Flight Mode of Aircra
2) GPS Status for Aircra
3) Watch Me/Follow Me Buon
4) In Flight Sengs
16. ST10+ DISPLAY
Double tap the center of the screen to
increase the size of the video viewing area.
WARNING: NEVER aempt to fly TYPHOON via
First-Person View (FPV). Aempng to fly via FPV
can result in a crash that will cause damage to the
product, property and/or cause serious injury.
IMPORTANT NOTE:
Aer flying, turn off TYPHOON BEFORE turning off
the ST10+. Then remove the baery from
TYPHOON and allow it to cool to ambient/room
temperature before recharging.
PILOT LOCATION
13-26 
(4-8m)
LANDING
LOCATION
Addional Smart Mode Features:
FOLLOW ME FUNCTION
The Follow Me funcon allows the TYPHOON to
follow the pilot, adjusng its locaon to the locaon
of the ST10+. This funcon is enabled when ST10+
GPS posioning completes, and the TYPHOON is
using shared GPS signal with the ST10+. At this me,
you will see orange , and green follow in .
When in Follow Me funcon, the TYPHOON will
WATCH ME FUNCTION
Watch Me funcon enables the camera to keep
tracking the remote controller no maer where and
how it moves as the camera can automacally lt its
angle according to the controller.
In Watch Me funcon, the pilot will always be kept in the
frame wherever he moves.
HOME MODE
When the Flight Mode Selecon Switch is in the
boom posion TYPHOON will be in Home (also
known as Return to Home) Mode.
1) When the flight mode switch is in the top posion
TYPHOON will be in Smart Mode.
2) When the flight mode switch is in the middle
posion TYPHOON will be in Angle (also known as
Pilot) Mode.
3) When the flight mode switch is in the lowest
posion TYPHOON will be in Home Mode.
14. FLIGHT MODES
SMART CIRCLE
In most cases the Smart Circle will keep TYPHOON
from coming within approximately 26 feet (8 meters)
of you (as long as you posion yourself at least 26
feet/8 meters behind TYPHOON.
In Home Mode the GPS connecvity will fly back
TYPHOON in a straight line in the direcon of the
pilots’ current locaon, and automacally land
within 13-26  (4-8m) of the pilot. This can be very
helpful for first-me pilots who aren’t quite ready to
land TYPHOON themselves. It can also be helpful
for pilots that lose orientaon during flight; simply
acvate Home Mode unl TYPHOON automacally
moves toward the home posion, and once you’ve
confirmed orientaon switch back to Angle (Pilot)
Mode. And if TYPHOON ever loses the link with the
ST10+ it will automacally enter Home Mode.
When Home Mode is acvated TYPHOON will
respond as follows:
1. CHARGING THE BATTERIES
2. INSTALLING THE PROPELLERS
Install the corresponding A and B propellers in the
posions shown by rotang them per the illustraon
and unl they’re secure. It may also be helpful to use
the included tool to hold the motors while installing
the propellers.
CAUTION: Do not over-ghten the propellers when
using the tool.
B
B
3. INSTALLING THE BATTERY
Never aempt to operate TYPHOON nearby tall
buildings/obstrucons that do not offer a clear view
of the sky (a minimum clearance of 100°).
Be sure to place TYPHOON on a level and stable
surface before powering ON the Controller and
Aircra.
Press here
This side
up
Addional Angle (Pilot)
Mode Feature:
POSITION HOLD AND
SELF-LEVELING
TYPHOON will automa-
cally hold its posion (with a
suitable GPS signal/lock)
and maintain a level atude
when the right-hand sck is
centered.
15. GIMBAL CONTROLS
A B
Use the slider (A) on the le side of the ST10+ to set
the pitch/lt posion (B) of the GB203.
A) When flying higher than 33 feet (10 meters)
TYPHOON will maintain the current altude, fly
back to the home point, or acve home point if the
ST10+ has enough satellites for Follow Me, then
descend vercally unl it lands.
B) When flying lower than 33 feet (10 meters)
TYPHOON will climb to 33 feet (10 meters) while
flying back to the home point, or acve home
posion, then will descend vercally unl it lands.
CAUTION: You must be certain there are no
obstacles in the ‘Return to Home’ flight path
otherwise TYPHOON may come into contact with
them and crash. While TYPHOON is in Home Mode
you will have a limited amount of direconal
control. To help avoid obstacles we strongly
recommend to switch to Smart or Angle Mode (then
you can switch back to Home Mode).
WARNING: Home Mode only works when
TYPHOON has a suitable GPS signal/lock. If
TYPHOON loses GPS signal/lock it will switch to
Angle (Pilot) Mode automacally. This is why we
strongly recommend learning to fly in Angle (Pilot)
Mode as soon as possible. Otherwise, if you lose
GPS signal/lock and are not able to properly control
TYPHOON in Angle (Pilot) Mode the aircra may
crash or even ‘fly away’.
IMPORTANT NOTE: Crash damage and ‘fly aways’
are NOT covered under warranty.
WARNING: If you do not properly control
TYPHOON in Angle (Pilot) Mode the aircra may
crash or even ‘fly away’.
IMPORTANT NOTE: Crash damage and ‘fly aways’
are NOT covered under warranty.
THE FOLLOWING DOCUMENTS ARE
AVAILABLE FOR DOWNLOAD AT
WWW.YUNEEC.COM/SUPPORT
• The full TYPHOON G Manual
Calibraon Sheet
LED Status Indicaon Sheet
Graphic User Interface
• Firmware Updates
• Tutorial Videos
Smart Circle
Mode 2 shown
This illustraon applies when the controller
is pointed towards the aircra
Mode 2 shown
> Mode 2 shown
TYPHOON G 2015.0831
A
A
IMPORTANT NOTE: All safety precauons and warnings, instrucons, warranes and other collateral informaon is subject to
change at the sole discreon of Yuneec. For the most up-to-date informaon please visit the corresponding product page at
www.Yuneec.com or contact the nearest Yuneec office or authorized distributor.
The following special language terms are used throughout the product literature to indicate various levels of potenal harm
when operang this product:
NOTICE: Procedures, which if not properly followed, create a possibility of property damage and/or lile to no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of property damage and/or a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage and/or
serious injury or create a high probability of superficial injury.
WARNING: Read the ENTIRE quick start guide and instrucon manual to become familiar with the features of the product
before operang. Failure to operate the product correctly can result in damage to the product, property and/or cause serious injury.
WARNING: This is a sophiscated consumer product. It must be operated with cauon and common sense, and requires some
basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in damage to the product,
property and/or cause serious injury. This product is not intended for use by children without direct adult supervision. Do not
use with incompable components or alter this product in any way outside of the instrucons provided by Yuneec. The quick
start guide and instrucon manual contain instrucons for safety, operaon and maintenance. It is essenal to read and follow
all the instrucons and warnings prior to assembly, setup and/or use in order to operate the product correctly and avoid damage
or serious injury.
AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.
GENERAL SAFETY PRECAUTIONS AND WARNINGS
WARNING: Failure to use this product in the intended manner as described in the quick start guide and instrucon manual can
result in damage to the product, property and/or cause serious injury. A Radio Controlled (RC) mulrotor aircra, APV plaorm,
drone, etc. is not a toy! If misused it can cause serious bodily harm and damage to property.
WARNING: As the user of this product you are solely and wholly responsible for operang it in a manner that does not endanger
yourself and others or result in damage to the product or the property of others.
Keep your hands, face and other parts of your body away from the spinning propellers/rotor blades and other moving parts at
all mes. Keep items that could impact or become entangled away from the propellers/rotor blades including debris, parts, tools,
loose clothing, etc.
Always operate your aircra in open areas that are free from people, vehicles and other obstrucons. Never fly near or above
crowds, airports or buildings.
To ensure proper operaon and safe flight performance never aempt to operate your aircra nearby buildings or other
obstrucons that do not offer a clear view of the sky and can restrict GPS recepon.
Do not aempt to operate your aircra in areas with potenal magnec and/or radio interference including areas nearby
broadcast towers, power transmission staons, high voltage power lines, etc.
Always keep a safe distance in all direcons around your aircra to avoid collisions and/or injury. This aircra is controlled by a
radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
To ensure proper and safe operaon of the automac landing funcon in Home Mode you must start the motors with the aircra
in a posion that has at least 10 feet (approximately 3 meters) of clear and open space around it and achieve a proper GPS lock.
Do not aempt to operate your aircra with any worn and/or damaged components, parts, etc. (including, but not limited to,
damaged propellers/rotor blades, old baeries, etc.).
Never operate your aircra in poor or severe weather condions including heavy winds, precipitaon, lightning, etc.
Always operate your aircra starng with a fully charged baery. Always land as soon as possible aer the first level low voltage
baery warning or land immediately aer the second level low voltage baery warning (as indicated by the vibraons and
audible alerts from the transmier/personal ground staon).
Always operate your aircra when the voltage of the baery in the transmier/personal ground staon is in a safe range (as
indicated by the baery charge status icon on the screen of the transmier/personal ground staon).
Always keep the aircra in clear line of sight and under control, and keep the transmier/personal ground staon powered on
while the aircra is powered on.
Always move the throle control sck down fully and turn off the motors in the event the propellers/rotor blades come into
contact with any objects.
Always allow components and parts to cool aer use before touching them and flying again.
Always remove baeries aer use and store/transport them per the corresponding guidelines.
Avoid water exposure to all electronic components, parts, etc. not specifically designed and protected for use in water. Moisture
causes damage to electronic components and parts.
Never place any poron of the aircra or any related accessories, components or parts in your mouth as doing so could cause
serious injury or even death.
Always keep chemicals, small parts and electronic components out of the reach of children.
Carefully follow the instrucons and warnings included with this aircra and any related accessories, components or parts
(including, but not limited to, chargers, rechargeable baeries, etc.).
CAUTION: The electronic speed controls (ESCs) installed in TYPHOON are not compable with any other product, and
TYPHOON is not compable with any other ESCs. Use of any other ESCs in TYPHOON will cause a crash, which may result in
damage to the product, property and/or cause serious injury.
BATTERY WARNINGS AND USAGE GUIDELINES
WARNING: Lithium Polymer (LiPo) baeries are significantly more volale than alkaline, NiCd or NiMH baeries. All instrucons
and warnings must be followed exactly to prevent property damage and/or serious injury as the mishandling of LiPo baeries
can result in fire. By handling, charging or using the included LiPo baery you assume all risks associated with LiPo baeries. If
you do not agree with these condions please return the complete product in new, unused condion to the place of purchase immediately.
You must always charge the LiPo baery in a safe, well-venlated area away from flammable materials.
Never charge the LiPo baery unaended at any me. When charging the baery you must always remain in constant observaon
to monitor the charging process and react immediately to any potenal problems that may occur.
Aer flying/discharging the LiPo baery you must allow it to cool to ambient/room temperature before recharging.
To charge the LiPo baery you must use only the included charger or a suitably compable LiPo baery charger. Failure to do so may
result in a fire causing property damage and/or serious injury.
If at any me the LiPo baery begins to balloon or swell, disconnue charging or discharging immediately. Quickly and safely
disconnect the baery, then place it in a safe, open area away from flammable materials to observe it for at least 15 minutes.
Connuing to charge or discharge a baery that has begun to balloon or swell can result in a fire. A baery that has ballooned or
swollen even a small amount must be removed from service completely.
Do not over-discharge the LiPo baery. Discharging the baery too low can cause damage to the baery resulng in reduced power,
flight duraon or failure of the baery enrely. LiPo cells should not be discharged to below 3.0V each under load.
Store the LiPo baery at room temperature and in a dry area for best results.
When charging, transporng or temporarily storing the LiPo baery the temperature range should be from approximately 40–120°
F (5–49° C). Do not store the baery or aircra in a hot garage, car or direct sunlight. If stored in a hot garage or car the baery can
be damaged or even catch fire.
Never leave baeries, chargers and power supplies unaended during use.
Never aempt to charge low voltage, ballooned/swollen, damaged or wet baeries.
Never allow children under 14 years of age to charge baeries.
Never charge a baery if any of the wire leads have been damaged or shorted.
Never aempt to disassemble the baery, charger or power supply.
Never drop baeries, chargers or power supplies.
Always inspect the baery, charger and power supply before charging.
Always ensure correct polarity before connecng baeries, chargers and power supplies.
Always disconnect the baery aer charging.
Always terminate all processes if the baery, charger or power supply malfuncons.
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide
reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio
communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful
interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operaon.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a
parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE WARNING
This equipment must be installed and operated in accordance with provided instrucons and the antenna(s) used for this transmier
must be installed to provide a separaon distance of at least 20 cm from all persons and must not be co-located or operang in
conjuncon with any other antenna or transmier. End-users and installers must be provide with antenna installaon instrucons
and transmier operang condions for sasfying RF exposure compliance.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operaon of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitaon est
autorisée aux deux condions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'ulisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est suscepble d'en compromere le fonconnement.
This equipment complies with IC RSS-102 radiaon exposure limit set forth for an uncontrolled environment.
Cet équipement respecte les limites d'exposion aux rayonnements IC définies pour un environnement non contrôlé
Model:TYPHOON Welcome,Pilot 07:25
GPS
N/A
SAT
N/A
POS
N/A E
N/A N
MODE
N/A
ALT
N/A 
VOLTS
N/A V
G-SPD
N/A mph
DIS
N/A 
System Sengs Flight Sengs Model Select
1
4
2
3
GEO-FENCE
The geo-fence is a virtual ‘barrier’ that will keep
TYPHOON from traveling further than 300 feet (91
meters). Although this limit can be adjusted using the
USB interface/programmer and soware we strongly
recommend using the default limit at all mes.
WARNING: Smart Mode only works when TYPHOON
has a suitable GPS signal/lock. If you take off in
Smart Mode and TYPHOON loses GPS signal/lock it
will switch to Angle (Pilot) Mode automacally. This
is why we strongly recommend learning to fly in
Angle (Pilot) Mode as soon as possible. Otherwise, if
you lose GPS signal/lock and are not able to properly
control TYPHOON in Angle (Pilot) Mode the aircra
may crash or even ‘fly away’.
IMPORTANT NOTE: Crash damage and ‘fly aways’
are NOT covered under warranty.
IMPORTANT NOTE: When the ST10+ Personal
Ground Staon is connected to less then 6 satellites,
the ‘FOLLOW ME’ feature will be disabled.
ANGLE (PILOT) MODE
When the Flight Mode Selecon Switch is the
middle posion TYPHOON will be in Angle (also
known as Pilot) Mode.
Angle (Pilot) Mode is the mode preferred by
experienced RC/drone pilots because TYPHOON
will move in the direcon the control sck is pushed
relave to the front/nose of the aircra. So if you
push the right-hand sck to the le TYPHOON will
bank toward the le side and move to the le. This
means if the front/nose of TYPHOON is poinng
away from you it will move to the le, but if the
front/nose is poinng at you TYPHOON will move
to the right.
If calibraon is needed before flight, Please press
calibraon buon enables the user to enter Compass
calibraon or Accelerometer calibraon. The
detailed calibraon operaon can be referred to the
User Manual on www.yuneec.com.
If indoor flight is needed, please turn off the GPS first.
Press seng buon on ST10+ interface and switch
off the GPS,
Watch Me/Follow Me Buon: When in Smart Mode, press
to switch the TYPHOON between Watch Me and Follow
me funcon. Follow Me funcon is the default seng, and
the buon is ORANGE. If it is GREY, it means ST10+ GPS
isn’t ready yet. Please wait.
Press , the buon will change from ORANGE to
GREEN. And now it is in Watch Me funcon.
NOTE: Once the TYPHOON is above 2m and out
of Smart Circle during flying, the TYPHOON yaw
direcon will take the control itself. Camera lens
will always point to you as long as Flight Mode
Selecon Switch is in Smart Mode. Please put the
GB203 Pitch Angle/Posion Control Slider in the
middle posion. If you want to trim camera angle
up, then just move the Pitch Angle/Posion
Control Slider a bit up. If you want to trim camera
angle down, just move the slider down.
follow the movement of ST10+ if there is no extra
operaon on the ST10+. The flight status is also
controllable when you operate ST10+ and GB203.
IMPORTANT NOTE: In Follow Me funcon, the
aircra will maintain a constant altude and cannot
detect obstacles. Pilots who change their altude by
for example, moving to higher ground, during flight
should be mindful of this.
9. BINDING THE MK58
STEP 1) Bind the MK58 to the Personal Ground
Staon/Remote Controller: Switch on the Personal
Ground Staon/Remote Controller and tap "Flight
Seng".
10 m
A
B
MODE
Follow
Any informaon above might be
changed due to the soware update.
For the latest documents, please check
the official website.
STEP 2) Select "Camera Select".
Model: Typhoon
Welcome,Pilot 10:48:28 pm
10
Bind
Camera Select
Hardware Monitor
Mode Select
STEP 6) Input password "12345678" and then tap
"OK". The binding succeeds.
STEP 7) Aer the Ground Staon/ Controller and
the MK58 are bound, the red LED of the MK58 will
blink. Press to return to the main interface of the
Ground Staon/Controller. The real-me images
can be shown on the interface of the Ground
Staon/ Controller.
STEP 3) Select "GoPro", tap "Select" and then tap
"OK". Then the Camera Mode is chosen.
STEP 4) Back to the previous interface and tap “Bind”.
STEP 5) Select the MK58 in "Camera" interface .
Model: Typhoon Welcome,Pilot 10:48:28 pm
10
GPS
Ready
SAT
13
POS
00.0000E
00.0000N
MODE
Angle
ALT
21.4 
VOLTS
12.3 V
G-SPD
0.0 mph
DIS
22.5 
System Sengs Flight Sengs
Model Select
HOME
Choose a camera NAME:
GOPRO
Model: Typhoon
Welcome,Pilot 10:48:28 pm
10
Model: Typhoon
Welcome,Pilot 10:48:28 pm
10
MK58
Model Camera
8. CAMERA CONTROL
Switch on the GoPro© camera. Please be sure to set
video mode for GoPro© Camera BEFORE starng the
motors of the aircra. Any operaon related to camera
controls should be referred to and downloaded
according to the official website of GoPro©.
The MK58 from YUNEEC extends the use of the
GB203 with real-me image transmission.
NOTICE: If install the GB203 on SteadyGrip,
GoPro© APP can be downloaded to achieve
real-me image transmission without MK58.
CAUTION: The GoPro© Wi-Fi will interfere with the
quadcopter receiver and may cause a loss of signal and
crash. Follow the camera instrucons to turn the Wi-Fi
off before aempng to power on the quadcopter.
Crash damage is not covered under warranty.
Model: TYPHOON Welcome,Pilot 10:48:28 pm 10
GPS
Ready
SAT
13
POS
00.0000E
00.0000N
MODE
watch
ALT
21.4 
VOLTS
12.3 V
G-SPD
0.0 mph
DIS
22.5 
System Sengs Flight Sengs Model Select
3840 x 2160 F30
Model: TYPHOON Welcome,Pilot 10:48:28 pm 10
GPS
Ready
SAT
13
POS
00.0000E
00.0000N
MODE
Follow
ALT
21.4 
VOLTS
12.3 V
G-SPD
0.0 mph
DIS
22.5 
System Sengs Flight Sengs Model Select
3840 x 2160 F30
Usually, the default funcon under Smart Mode is
Follow Me. Watch Me funcon can be switched to
by following steps:
PROCESS IS COMPLETE. The main LED status
indicator will glow solid green (Smart Mode) or solid
purple (Angle/Pilot Mode) when inializaon is
complete (and TYPHOON GPS is locked). The GB203
LED status indicator will blink green slowly when
inializaon is completed. The MK58 will be supplied
with power. Then the blue LED of the MK58 is on.
4. PREPARING THE MK58
Step 1)
Plug the audio connector into audio port of
the MK58; then plug the 4PIN power connector into
power output port of GB203.
STEP 2)
Plug the MINI USB connector into USB
interface of GoPro© Camera
Audio
Connector
MINI USB
4PIN
Climb (Max. Altude
400 Feet / 122 Meters)
Maximum Climb Rate:
2m/s (6.6f/s)
Maintain Altude
Descend / Land
Mode 2 shown
3
4
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yuneec Typhoon G bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yuneec Typhoon G in de taal/talen: Engels als bijlage per email.

De handleiding is 1,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Yuneec Typhoon G

Yuneec Typhoon G Gebruiksaanwijzing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info