669800
25
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
BINDING (SINGLE MODE)
The TORNADO H920 and ST24 have already been bound before leaving production, so
there is no need to bind the aircraft to the ST24 if no gimbal is used. If the GB603 gimbal
is to be attached to the aircraft, both the GB603 and TORNADO H920 need to be bound.
BINDING THE TORNADO H920 AND GIMBAL/GIMBAL CAMERA TO THE ST24
NOTICE: Attach the camera to GB603 camera gimbal before powering on the ST24.
STEP 1) Power on the ST24, press [ ] to go to the main interface. Choose FPV, and
enter Model Select.
STEP 2) The default Model type is Multi-copter, and choose the right configuration
you are using the H920/GB603, H920/V18 and the H920/CGO4. Press OK when a
pop-up window comes out.
STEP 3)
For GB603, switch on the LK58 (the switch is
located between the two antennas) and the camera.
STEP 4) Select System Settings
STEP 5) Switch on the TORNADO H920.Wait until the
Main LED indicator blinks blue, Gimbal roll axis stays
horizontal, one of the LK58 LED indicator solid red and the
other blinking blue (only for GB603). Then it means the
self-inspection of the H920 and the gimbal is complete.
NOTICE: For GB603, the receiver will blink orange quickly if the GB603 is installed a receiver.
Tap the refresh icon and the receiver code of GB603 will be shown on the screen. Do not
choose it to bind.
STEP 6) Lean the H920 in the forward direction twice (45°)until the Main LED
indicator blinks yellow.
STEP 7) Tap the Refresh icon again, and the
codes of the H920 will be shown on screen.
Choose the receiver code and WIFI codes
shown below the MODEL and CAMERA
columns simultaneously, and press Bind.
STEP 8) if it is the first time to bind your LK58
(v18/cgo4) to the ST24,you need to input the
password: 87654321 (for LK58 and V18), or
1234567890 (for CGO4), press OK on the
pop-up window to continue.
STEP 9) Wait till the WIFI signal icon appears, Press Camera Select and choose
Panasonic GH4 or Sony α7 for GB603 or V18/CGO4. Press select, then press OK.
NOTICE: If the model chosen has never be bound before, 'NOT CONNECTED' will
display in the MODEL column, and the remote controller can bind any YUNEEC
SR12/24 receiver. If a series of receiver codes display on the screen, it means the
model was bound before and can't be bound to any other receiver. If you want to bind
this model to other receiver,you can press and hold the model icon in the MODEL
24
PADFPVRC
ST24
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yuneec Tornado H920 Industry bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yuneec Tornado H920 Industry in de taal/talen: Engels als bijlage per email.

De handleiding is 3,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info