557718
7
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
5
English
Speaker cables typically consist of two insulated
conductors. To ensure that the speakers are connected with
the correct polarity (+/-), the insulation on one of the
conductors is a different color or is marked with a line.
1. Strip about 15 mm (5/8”) of insulation from
the ends of the speaker cables.
2. Twist the bare wires tightly to prevent a
short circuit.
3. Unscrew the SPEAKER terminals.
4. Insert the twisted bare wires into the holes
on the SPEAKER terminals.
5. Screw the SPEAKER terminals tight.
When using banana plugs, tighten the terminal knob
and insert the plug into the end of the terminal.
(With the exception of U.K., Europe and Korea models)
Connecting to the BALANCE jacks
Connect your component with the balanced XLR
output jacks.
The pin assignments for these jacks are shown below.
Refer to the owners manual of your component and
verify that its output jacks are compatible with the pin
assignments for these jacks.
When connecting, match the pins and insert the
connector of the XLR cable until you hear a “click.”
When disconnecting, pull out the XLR cable while
holding down the lever of the BALANCE jack.
When using this balanced connection, set the UNBAL/
BAL switch to “BAL.”
Connecting to the UNBALANCE jacks
Connect your component with the unbalanced RCA
output jacks.
When using this unbalanced connection, set the
UNBAL/BAL switch to “UNBAL.”
Do not connect your components to both of the
BALANCE jacks and UNBALANCE jacks.
Plug the power cable into the AC IN connector when all
connections are complete, and then plug in the power
cable to the AC outlet.
Caution
When inserting the stripped ends of the speaker
wires as shown above, make sure at least 1/16
inch (1.6 mm) of insulation is inside the wire
holders (i.e no exposed wire is visible) and no
loose conductor wire strands are protruding
after connection. If wires touch each other or
they touch the metal parts of this unit, this unit
and/or speakers could be damaged. To prevent
speaker wire from coming loose, make sure wire
holder are firmly screwed in.
Connecting Your Speakers
15mm
1
2
4
33
5
Red: + (positive)
White: - (negative)
Banana plug
Connecting Your Source
Components
2: hot
1: ground
3: cold
Caution
Connecting the Power
Cable
01-MX-D1_GB_E.fm Page 5 Wednesday, October 22, 2003 2:05 PM
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yamaha MX-D1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yamaha MX-D1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Zweeds als bijlage per email.

De handleiding is 4,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info