557718
5
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
3
English
1 STANDBY/ON switch/indicator
This switch is used to set the MX-D1 to on or standby. A small amount of power is used in standby mode.
When the MX-D1 is turned on, this indicator lights blue and the MX-D1 is ready for use.
When the internal temperature rises, this indicator lights blue and purple alternately. If this happen, relocate this unit in a
well ventilated place and turn down the volume of the pre-amplifier etc.
When a fault is detected, the MX-D1’s protection system activates and this indicator lights red. If this happens,
set the MX-D1 to standby mode immediately and disconnect the AC power cable from the AC outlet.
If the indicator continues to light red when you re-connect the AC power cable, contact the nearest Yamaha dealer.
2 SPEAKER terminals
These terminals are for connecting your speakers.
They provide a reliable connection even with really
thick cables. Be sure to connect the left and right
channels, and the speaker polarities (+/-) correctly.
You can connect speakers with impedance of between
4 to 8 ohms.
3 BALANCE jacks
If your source component has balanced XLR output
jacks, connect them to these jacks using XLR cables.
4 MUTE button
You can temporarily mute the output from the MX-D1
by holding down this button. If you need to change
any input connections while the MX-D1 is still on,
hold down this button while you do it. This will
protect your speakers against possible damage due to
sudden loud noises, thumps, and clicks.
5 UNBALANCE jacks
If your source component has unbalanced RCA jacks
(labeled “AUDIO OUTPUT” on the YPC-1), connect
them to these jacks using an audio pin cable.
6 UNBAL/BAL switch
With this switch you can select the BALANCE jacks
or the UNBALANCE jacks.
7 AC IN connector
Connect the supplied AC power cable here.
e POWER switch
(Australia, U.K., Europe, China and Korea models)
Normally, set this switch to the ON position to use the
MX-D1.
To cut off the power supply from the AC line, set this
switch to the OFF position.
8 RS-232C terminal
9 AMP ID switch
0 CONTROL IN jack
q CONTROL OUT jack
w POWER/THROUGH switch
These are for control expansion. Consult your dealer
for details.
01-MX-D1_GB_E.fm Page 3 Wednesday, October 22, 2003 2:05 PM
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yamaha MX-D1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yamaha MX-D1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Zweeds als bijlage per email.

De handleiding is 4,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info