571272
263
Verklein
Vergroot
Pagina terug
1/300
Pagina verder
Reference Utility Mode
Utility mode
263
Owner’s Manual
SongEventChase Event Chase allows you to specify which non-note data types are properly recognized during fast-forward and
rewind operations. Normally, if a Song or Pattern is played back from mid-point and/or fast-forward or rewind are
used, certain data types (such as Program Change, Pitch Bend, and Control Change) may not play back as
expected. Setting this to a specific event ensures the playback integrity of the event, even when fast forwarding or
rewinding.
Settings: Off, PC (Program Change), PC+PB+Ctrl (Program Change+Pitch Bend+Control Change), all (All events)
nKeep in mind that settings other than “off” may result in slower operation — for example, a pause before starting playback, or
slower rewind/fast forward speed.
nWhen this is set to “all,” an excessive amount of MIDI data may be generated, possibly resulting in a MIDI error on the
connected device.
DumpInterval (Bulk Dump
Exclusive Interval Time) When playing back system exclusive data (bulk data) that is recorded on the sequence tracks, this sets the interval
that is inserted for each 1KB.
When sending bulk data from this synthesizer to a connected MIDI device, a MIDI error may result if the device
cannot handle large amounts of data in a short time. This parameter compensates for that by setting an interval that
provides enough time for the receiving device to process the bulk data.
Settings: 0 ~ 900 (msec)
nThe playback may be a little slower depending on the currently set interval. Also when a MIDI error occurs, try to set the
interval a little higher and send the data again.
LoadMix Determines whether the Mixing settings are loaded (on) or not (off) when the Song/Pattern number is changed.
Settings: off, on
nThis setting affects the Song/Pattern change during Song/Pattern chain playback.
SendXGOn
ToMultiPartPB Determines whether an XG reset message is sent to the Multi-part Plug-in board tone generator block (on) or not
(off) when starting an XG song or changing the Song/Pattern number.
Settings: on, off
[F4] CTL ASN (Controller Assign)
[SF1] ARP (Arpeggio)
Switch Determines the Control Change Number that controls on/off status of Arpeggio playback.
Settings: 00~95
Hold Determines the Control Change Number that controls on/off status of Arpeggio Hold (page 189).
Settings: 00~95
[SF2] ASSIGN From this display you can assign specific functions to the ASSIGN A and B knobs (when the [PAN/SEND] and
[TONE] lamps are on).
ASA (Assign A)
Dest (Destination) Two parameters are available here. The first (ASA) determines the Control Change number generated by the
ASSIGN A knob. The second, Destination (Dest), determines what parameter or aspect of the sound is affected by
the knob. Keep in mind that if the same MIDI Control Change messages as set here are received from an external
device, the internal tone generator also responds to those messages.
Settings: Refer to the separate Data List booklet.
ASB (Assign B)
Dest (Destination) Two parameters are available here. The first (ASB) determines the Control Change number generated by the
ASSIGN B knob. The second, Destination (Dest), determines what parameter or aspect of the sound is affected by
the knob. Keep in mind that if the same MIDI Control Change messages as set here are received from an external
device, the internal tone generator also responds to those messages.
Settings: Refer to the separate Data List booklet.
[SF3] FT SW (Footswitch) From this display you can determine the Control Change number generated by using the Footswitch connected to
the ASSIGNABLE jack. Keep in mind that if the same MIDI Control Change messages as set here are received from
an external device, the internal tone generator also responds to those messages as if the Footswitch of the
instrument was used.
Settings: 000~100 (000, 032: off, 096: Arpeggio Switch, 097: Arpeggio Hold, 098: Song/Pattern playback start/stop, 099/100: Program
Change INC/DEC 101: Octave Rest)
[SF4] REMOTE Two different computer sequencer control modes can be selected here, as well as the respective MIDI port settings
for control. When you’ve made the desired settings, press the [ENTER] button to actually call up the preset control
templates for the software. For details, refer to the Quick Guide on page 147.
[SF5] MEF (Master Effect) From this display you can set the parameters related to the Master Effect Knob operations. (Press both the [ARP FX]
and [EQ] buttons so that their lamps light.)
Knob1 ~ Knob4 Assigns a parameter of the Master Effect to each knob. Available parameters differ depending on the selected
Master Effect type.
[F5] MIDI
[SF1] CH (Channel) From this display you can make basic MIDI settings.
BasicRcvCh
(Basic Receive Channel) Determines the MIDI receive channel when this synthesizer is set to single-timbre tone generator mode (Voice/
Performance modes).
Settings: 1~16, omni (all channels), off
nIn the multi-timbral tone generator mode (Song/Pattern modes), each Part receives MIDI data according to its assigned MIDI
receive channel ([SONG] or [PATTERN] [MIXING] [EDIT] Part selection [F1] VOICE [SF2] MODE ReceiveCh).
263

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yamaha MOTIF ES7 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yamaha MOTIF ES7 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Yamaha MOTIF ES7

Yamaha MOTIF ES7 Gebruiksaanwijzing - Nederlands - 300 pagina's

Yamaha MOTIF ES7 Installatiehandleiding - Deutsch - 35 pagina's

Yamaha MOTIF ES7 Gebruiksaanwijzing - Deutsch - 300 pagina's

Yamaha MOTIF ES7 Installatiehandleiding - English - 35 pagina's

Yamaha MOTIF ES7 Gebruiksaanwijzing - Français - 300 pagina's

Yamaha MOTIF ES7 Installatiehandleiding - Français - 35 pagina's

Yamaha MOTIF ES7 Gebruiksaanwijzing - Italiano - 308 pagina's

Yamaha MOTIF ES7 Installatiehandleiding - Italiano - 12 pagina's

Yamaha MOTIF ES7 Gebruiksaanwijzing - Português - 300 pagina's

Yamaha MOTIF ES7 Gebruiksaanwijzing - Espanõl - 297 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info