517044
292
Verklein
Vergroot
Pagina terug
1/308
Pagina verder
MIDI-Datenformat 291
01V—Bedienungsanleitung
PARAMETER CHANGE(type 0x05:remote meter)
When the following request is received to enable transmission, the
specified parameter data will be transmitted at 30 msec intervals for
five seconds. If you want meter data to be transmitted continuously,
you must continue transmitting requests less than five seconds apart.
Reception
When [Parameter Change RX] is ON and the [Rx CH] matches the
Device Channel that is included in the SUB STATUS, this message is
received.
When [LOCAL OFF] is ON, the incoming meter data will be dis-
played. In other cases it will be ignored.
Transmission
When transmission is enabled by a request, this will be transmitted
every 30msec on the [Rx CH] channel, for five seconds.
Transmission will be disabled when the power is turned on, and when
PORT settings have been modified.
In the Meter no., bit 6 is the special bit, and bit 5 is the gr bit.
When the Gr bit is on, the single byte gr will be added uniformly to
the end of the data string.
When the Special bit is on, the two bytes stLED L/R will be added uni-
formly to the end of the data string.
When both are on, gr comes first, and stLED L/R come later.
PARAMETER VALUE REQUEST(type 0x05:remote
meter)
This message is used to obtain meter data from the 01V. It is used in
LOCAL OFF MODE to display the meter of the remote device, or to
display the meter on the screen of a personal computer, etc.
In order to obtain meter data, the meter whose data is required must
be displayed in the LCD of the remote device. This means that before
transmitting this request, you must first transmit the
above-described "4.6.4.11 PARAMETER CHANGE (type 0x03:bit
operation for controller(LCD-Fader mode))" to display the appro-
priate meter in the LCD screen of the remote device.
Reception
When [Parameter Change RX] is ON and the [Rx CH] matches the
Device Channel included in SUB STATUS, this message will be
received.
When this message is received, Parameter Change (remote meter)
messages will begin to be transmitted on the [Rx CH] channel.
Transmission
When [LOCAL OFF] is ON, transmit a meter data request for the
currently displayed meter on the [Tx CH]. For each request, meter
data will be transmitted for five seconds. If you want meter data con-
tinuously for longer than this, you will need to transmit requests at
intervals of five seconds or less. When the 01V is in LOCAL OFF
MODE, transmit requests at approximately one-second intervals.
When [Parameter Change ECHO] is ON and the 01V itself did not
receive this message, the message will be echoed.
Table of signal levels and codes
5. SYSTEM EXCLUSIVE
MESSAGE (Bulk Dump) &
REQUEST
These messages input and output the contents of various types of
internal memory.
The unique header identifies whether or not the data is for the 01V.
The CHECK SUM is calculated by adding the data following the
BYTE COUNT(LOW) until the data preceding the CHECK SUM,
then inverting the bits (2's complement), and setting bit 7 to 0.
CHECK SUM = ( -sum) & 0x7F
Reception
This is received if [Bulk RX] is ON and the [Rx CH] matches the
Device Channel that is included in SUB STATUS.
When a BULK DUMP is received, it will immediately be written into
the specified memory.
When a BULK DUMP REQUEST is received, a bulk dump will be
transmitted immediately.
Transmission
In the [MIDI-BULK] page, this is transmitted on the [Tx CH] chan-
nel by key operations.
In response to a Bulk Dump Request, a Bulk Dump Message is trans-
mitted on the [Rx CH] channel.
STATUS 11110000 F0 System Exclusive Message
ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)
SUB STATUS 0001nnnn 1n n=0-15(Tx/Rx Channel No.1-16)
GROUOP ID 00111110 3e MODEL ID
MODEL ID 00000100 04 Device code (01V)
PARAM TYPE 00000101 05 remote meter
DATA 0sgttttt tt meter no.(s:special bit, g:gr bit)
0mmmmmmm mm0
0mmmmmmm mm1
: :
EOX 11110111 F7 End Of Exclusive
STATUS 11110000 F0 System Exclusive Message
ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)
SUB STATUS 0011nnnn 3n n=0-15(Tx/Rx Channel No.1-16)
GROUOP ID 00111110 3e MODEL ID
MODEL ID 00000100 04 Device code (01V)
PARAM TYPE 00000101 05 remote meter
DATA 0sgttttt tt meter no.(s:special bit, g:gr bit)
EOX 11110111 F7 End Of Exclusive
Level code Level code Level code
------------------------------------------------------------------------------------
-
-72dB 0x1F -30dB 0x57 -9dB 0x72
-68dB 0x24 -27dB 0x5A -8dB 0x73
-64dB 0x29 -24dB 0x5F -7dB 0x75
-60dB 0x2F -21dB 0x62 -6dB 0x77
-56dB 0x33 -18dB 0x67 -5dB 0x78
-51dB 0x3A -16dB 0x69 -4dB 0x79
-48dB 0x3F -15dB 0x6A -3dB 0x7A
-46dB 0x41 -14dB 0x6B -2dB 0x7B
-42dB 0x47 -13dB 0x6D -1dB 0x7D
-39dB 0x4A -12dB 0x6F 0dB 0x7E
-36dB 0x4F -11dB 0x70 CLIP 0x7F
-33dB 0x52 -10dB 0x71
data name rx/tx function
------------------------------------------------------------------------------------------------------
'M' rx/tx Scene Memory & Request
'S' rx/tx Setup Memory & Request
'I' rx/tx Remote(Internal Parameter) Memory & Request
'L' rx/tx Remote(MMC) Memory & Request
'U' rx/tx Remote(User Define) Memory & Request
'C' rx/tx Control Change Assign Table & Request
'P' rx/tx Program Change Assign Table & Request
'Q' rx/tx Equalizer Library & Request
'Y' rx/tx Dynamics Library & Request
'E' rx/tx Effect Library & Request
292

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Yamaha-01V

Zoeken resetten

  • kan ik meerdere inputs op 1 compressor toewijzen.
    Ik zou nl een 6tal microfoons door de compressor willen halen.
    Er zijn echter maar 3 compressors ter beschikking.
    Als ik comp1 toewijs aan ch 1 werkt dit op dit kanaal.
    Als ik echter ch 2 oproep en ik wijs daar ook comp 1 aan toe verdwijnt de comp op ch1 Gesteld op 10-9-2021 om 19:28

    Reageer op deze vraag Misbruik melden
  • heb al meer dan 12 jaar plezier van mijn ov1 yamaha mengtafel met automatische faders , sinds een paar maanden valt hij af en toe uit , moet er een interne batterij worden vervangen of is het slijtage? Gesteld op 9-9-2019 om 10:30

    Reageer op deze vraag Misbruik melden
    • Wat valt er uit? Het hele apparaat, het geheugen, het display, of audio aan de uitgang? Als het instellingen zijn van het geheugen zal het de interne batterij zijn. Geantwoord op 9-9-2019 om 20:19

      Waardeer dit antwoord Misbruik melden
    • Dank u wel voor het antwoord , nu weer terug naar mijn probleem:het hele apparaat valt uit , namelijk er komt geen audio meer door en het display vertoond hele rare afbeeldingen , dus wat te doen ? Geantwoord op 9-9-2019 om 21:11

      Waardeer dit antwoord (2) Misbruik melden
    • Resetten naar fabrieksinstellingen zou je eens kunnen proberen (zie initialiseren blz. 204 NL-handleiding). Let op: Alle opgeslagen instellingen raak je dan wel kwijt! -Memory knop ingedrukt houden, en dan aanzetten-. Geantwoord op 9-9-2019 om 21:23

      Waardeer dit antwoord (2) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yamaha 01V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yamaha 01V in de taal/talen: Duits als bijlage per email.

De handleiding is 5,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Yamaha 01V

Yamaha 01V Gebruiksaanwijzing - Nederlands - 314 pagina's

Yamaha 01V Gebruiksaanwijzing - English - 303 pagina's

Yamaha 01V Gebruiksaanwijzing - Français - 299 pagina's

Yamaha 01V Gebruiksaanwijzing - Italiano - 313 pagina's

Yamaha 01V Gebruiksaanwijzing - Português - 94 pagina's

Yamaha 01V Gebruiksaanwijzing - Espanõl - 314 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info