655217
15
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
15
Low Battery Indication
The App will display the low battery message under the
actual device.
When a device rst shows the low battery signal it has
enough battery capacity to operate for a further month
before complete exhaustion.
Door/Window Contact Battery Change
When the battery is low the LED will light up when the
door/window is opened. The battery is changed as follows:
1. Ensure the system is disarmed.
2. Loosen the case screw and remove the Door/Window
Contact from the base to reveal battery.
3. Using a screwdriver gently lever out the old battery.
4. Insert new CR2032 coin cell battery with the + side
uppermost. See picture on page 16.
5. Press battery into holder rmly with nger and thumb
until a click is heard.
6. Ret sensor on base and tighten bottom case screw.
Switch tamper protection back on.
Door/Window Contact case tamper conditions are also
indicated by a lit LED, check the tamper before changing
the battery.
PIR Motion Detector & Image / Video Camera
Battery Change
When the battery is low the LED will ash when any motion
is detected. The batteries are changed as follows:
1. Ensure the system is disarmed.
2. Loosen the case screw and remove PIR from base to
reveal the batteries.
3. Insert new batteries observing correct polarity. (Note:
PIR Motion Detector takes 3x AAA alkaline batteries, PIR
Image Camera takes 2x AA alkaline batteries and PIR
Video Camera takes 3 x AA Lithium batteries. The PIR
LED will ash for 30 seconds while initialising.
4. Ret PIR on base and tighten bottom case screw.
Ensure tamper spring is fully depressed when re-tting
the PIR to the back case. If this has not been done
correctly this will be indicated by a ashing LED on the
PIR.
External Siren Battery Change
When the batteries start getting low the Siren will produce
a series of audible pips and ashes during arming and
disarming.
1. Ensure the system is disarmed. Select “Controller”,
Device List”, click Siren’s Properties (icon on the right)
and set Siren Bypass to the OFF position.
2. Remove the Siren lid and switch the Siren power switch
to OFF.
3. Unscrew the four screws on the battery compartment lid
and remove the cover.
4. Remove the four batteries, wait for 30 seconds, and
replace them with four fresh alkaline “D” batteries.
5. Switch on Siren power and check that the Siren beeps
and ashes.
Warning: After the batteries have been inserted, the
tamper will become active after three hours. Please replace
the cover back onto the Siren quickly.
Siren case tamper conditions are also signalled by a
series of beeps when the system is armed but not when
the system is disarmed (low battery warning produces a
series of audible pips when armed and disarmed), take
care not to confuse the two dierent conditions.
Changing the Batteries
8
Always use correct type of batteries as replacements because any other battery can
cause problems with the operation of the system. Ensure the correct steps are taken
when changing batteries in tamper protected devices.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yale SR310 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yale SR310 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info