655217
14
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
14
Reset Key Pad code
If the Key Pad code is accidentally forgotten, the Key Pad
can be reset to factory default (0000) using the following
steps:
1. Unscrew the two Key Pad case screws and remove Key
Pad back cover (please disable tamper rst).
Locate and remove the battery. See battery change
section (16-17)
2. Press the number ‘4’ key at the same time as reinserting
the battery.
3. Screw the Key Pad case together and re-learn the Key
Pad into the system using the steps described above in
this section.
Using your Key Pad
The Key Pad can be used to Away Arm and Home Arm
the system using the buttons as shown.
The system is disarmed by pressing the disarm button
followed by your PIN code.
An emergency alarm can be activated by pressing the
panic A and B buttons simultaneously. Deactivate panic
event by pressing the disarm button followed by your PIN
code.
If there is a system fault, you will need to press the Arm/
Home Arm button for a second time to “force arm” the
system.
Using your Smoke Detector
Smoke Detection
When smoke is detected the device will activate for a
minimum of 10 seconds with a two tone alarm and ashing
LED. The Detector will send a radio signal to the Smart
Hub. You will then be notied via a push notication, SMS
and email .
Pressing the test button when in an alarm condition will
silence the alarm for 10 minutes. It will automatically
resume smoke detection again after this period.
Testing
Smoke Detector testing should be done on a regular
monthly basis. Pressing the test button will make the LED
ash, the audible sounder chime and will send a radio
test signal to the Smart Hub when the button is released.
If nothing happens after pressing the test button, it
indicates the batteries will need changing.
Recalibration
The Smoke Detector might need recalibrating after time
to ensure it is working at its optimum. This is done by
pressing and holding the test button until the LED ashes
and beeps after 10 seconds. The Detector will then start
its self calibration routine.
Using your Panic Button
Activate an Alarm
Press and hold the red button for at least 3 seconds. The
LED will light momentarily and the alarm will be activated.
Silence an Alarm
1. Press and hold down the red button for 10 seconds.
The LED will light momentarily for a second time and the
alarm will be silenced.
2. Please note that silencing the alarm with the Panic
Button does not reset the system. If the alarm is armed
prior to activation, the system will re-arm after being
silenced with the Panic Button.
3. The system will require a reset at the Smart Hub after
being silenced with the Panic Button.
Using Accessories (cont.)
7
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yale SR310 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yale SR310 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info