478504
60
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
Page 58 FT-950 OPERATING MANUAL
The Automatic Antenna Tuner (hereinafter referred to as the “ATU”) built into each FT-950 is designed to ensure a 50-
Ohm load for the final amplifier stage of the transmitter. We recommend that the ATU be used whenever you operate on the
FT-950.
ADVICE:
Because the ATU of the FT-950 is located inside the station, it only adjusts the impedance presented to the transceiver
at the station end of your coaxial cable feedline. It does not “tune” the SWR at the antenna feed point itself. When
designing and building your antenna system, we recommend that every effort be made to ensure a low SWR at the
antenna feed point.
The ATU of the FT-950 includes 100 memories for tuning data. Eleven of these memories are allocated, one per
Amateur band, so that each band has at least one setting preset for use on that band. The remaining 89 memories are
reserved for the 89 most-recent tuning points, for quick frequency change without the need to retune the ATU.
The ATU in the FT-950 is designed to match impedances within the range of 16.5 Ohms to 150 Ohms, corresponding
to an SWR of 3:1 or less on the 160 through 6 meter amateur bands. Accordingly, simple non-resonant whip antennas,
along with random-length wires and the “G5RV” antenna (on most bands) may not be within the impedance matching
range of the ATU.
ATU OPERATION
USING THE AUTOMATIC ANTENNA TUNER
1. Use the Main Tuning Dial knob to set the radio to the
desired operating frequency within the Amateur band.
2. Press the
[
TUNE
]
button momentarily to place the ATU
in the transmit line (no adjustment/tuning will occur
yet). The “ ” icon will appear in the display.
QUICK POINT:
The momentary press of the
[
TUNE
]
button will turn
the tuner on, and the microprocessor will automatically
select the tuning point closest to the current operating
frequency.
3. Press and hold in the
[
TUNE
]
button for one second to
begin automatic tuning. The transmitter will be en-
gaged, and the “ ” icon will blink while tuning
is in progress. When the optimum tuning point has been
reached, the radio will return to receive, and the
” icon will again glow steadily (instead of
blinking).
4. To disconnect the ATU from the transmit line, press
the
[
TUNE
]
button momentarily. The “ ” icon
will turn off, confirming that the ATU has been turned
off. In the “Off” mode, the transceiver will be directly
connected to the coaxial cable connected to your an-
tenna, and will operate based on whatever impedance
is present at the station end of the coax.
ADVICE:
The ATU circuit is located between the final amplifier and
the rear-panel antenna jack; reception is not affected by
the ATU.
QUICK POINTS:
As shipped from the factory, only one ATU alignment point
is saved on each Amateur band. This was memorized dur-
ing the final alignment and performance verification stages
on the production line.
NOTE:
Please check the operating frequency before beginning the
tuning process, to be sure you are not interfering with oth-
ers who may already be using the frequency.
TERMINOLOGY:
Antenna Tuner Memories: The microprocessor of the ATU
makes a note of the positions of the tuning capacitors and
the selected inductors, and stores the data for each 10 kHz
window in which tuning has occurred. This eliminates the
need to re-tune every time you return to a frequency on
which you have already completed the tuning process.
[
TUNE
]
Button
60

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Yaesu-FT-950

Zoeken resetten

  • Ft950 wil niet zenden met jtdx in ft8 ontvangt wel goed settings staan volgens Manuel ingesel, e weet raad? 73 PD4 PG Gesteld op 22-7-2024 om 22:04

    Reageer op deze vraag Misbruik melden
  • Bij het opstarten knippert TX. Ontvangst doet het, maar zenden niet. Wie heeft een oplossing? Gesteld op 15-4-2024 om 14:09

    Reageer op deze vraag Misbruik melden
  • Hoe sluit ik een digibox (MMSTV) aan op een FT950? Gebruikte voorheen een FT575GX2 . Deze had 3 tulpstekkertjes. Audio in audio uit en PTT ontvangst werkt goed en de zender schakelt ook in. Audio signaal klinkt niet zoals het hoort. Gesteld op 28-7-2023 om 19:00

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-950 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-950 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info