478497
21
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
Page 19FT-2000D OPERATING MANUAL
FRONT PANEL CONTROLS & SWITCHES
NB Switch
This button turns the IF Noise Blanker on and off.
Press this button momentarily to reduce a short-dura-
tion pulse noise; the “ ” icon will appear in the dis-
play.
Press and hold in this button for one second to reduce
a longer-duration man-made pulse noise; the “
icon will blink for three seconds, then will appear con-
tinuously in the display.
Press this button again to disable the noise blanker;
the “ ” icon will disappear.
ADVICE:
When you press (or press and hold) the
[
NB
]
button
momentarily, it affects the Main band (VFO-A) re-
ceiver. When you press the
[
B
]
button, then press (or
press and hold in) the
[
NB
]
button (within five sec-
onds of pressing the
[
B
]
button), it affects the Sub band
(VFO-B) receiver.
METER Switch
This control switch determines the function of the meter
during transmission.
COMP: Indicates the speech compressor level (SSB
mode only).
ALC: Indicates the relative ALC voltage.
PO: Indicates the average power output level.
SWR: Indicates the Standing Wave Ratio (Forward:
Reflected).
ID: Indicates the final amplifier drain current.
VDD: Indicates the final amplifier drain voltage.
MONI PROC Knobs
MONI Knob
The inner
[
MONI
]
knob adjust the audio level of the
transmit monitor during transmission (relative to the
AF GAIN control), when activated by the
[
MONI
]
button.
PROC Knob
The outer
[
PROC
]
knob sets the compression (input)
level of the transmitter Speech Processor in the SSB,
AM, and FM modes, when activated by the
[
PROC
]
button.
ADVICE:
The Sub band (VFO-B) frequency display will show
the compression level of the Speech Processor for 3
seconds whenever the outer
[
PROC
]
knob is turned.
You may disable this feature (displaying the compres-
sion level) via Menu item “015 diSP LVL IND.” See
page 117 for details.
BK-IN Switch
This button turns the CW break-in capability on and
off. While the CW break-in is activated, the “
icon appears in the display.
SPOT Switch
This button turns on the CW receiver spotting tone; by
matching the SPOT tone to that of the incoming CW
signal (precisely the same pitch), you will be “zero
beating” your transmitted signal on to the frequency of
the other station.
The Sub (VFO-B) frequency display will indicate the
offset tone frequency when this button is pressed.
SPEED PITCH Knobs
SPEED Knob
The inner
[
SPEED
]
knob adjusts the keying speed of
the internal CW keyer (4 ~ 60 WPM). Clockwise rota-
tion increases the sending speed.
When turning this knob while pressing the
[
KEYER
]
button, the Sub (VFO-B) frequency display shows the
keying speed.
ADVICE:
The Sub band (VFO-B) frequency display will show
the keying speed for 3 seconds whenever the inner
[
SPEED
]
knob is turned.
You may disable this feature (displaying the keying
speed) via Menu item “015 diSP LVL IND.” See page
117 for details.
PITCH Knob
The outer
[
PITCH
]
knob selects your preferred CW
tone pitch (from 300 ~ 1050 Hz, in 50 Hz increments).
The Tx sidetone, receiver IF passband, and display
offset from the BFO (carrier) frequency are all affected
simultaneously. The Pitch control setting also affects
the operation of the CW Tuning Indicator, as the cen-
ter frequency of the CW Tuning Indicator will follow
the setting of this control.
ADVICE:
The Sub band (VFO-B) frequency display will show
the CW tone pitch frequency for 3 seconds whenever
the outer
[
PITCH
]
knob is turned.
You may disable this feature (displaying the CW tone
pitch frequency) via Menu item “015 diSP LVL IND.”
See page 117 for details.
NB SQL Knobs
NB Knob
The inner
[
NB
]
knob adjusts the noise blanking level
when the (analog) IF noise blanker is activated by press-
ing the
[
NB
]
button.
SQL Knob
The outer
[
SQL
]
knob sets the signal level threshold
at which the Main (VFO-A) receiver audio is muted,
in all modes. It is very useful during local rag-chews,
to eliminate noise between incoming transmissions.
This control is normally kept fully counter-clockwise
(off), except when scanning and during FM operation.
21

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Yaesu-FT-2000D

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-2000D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-2000D in de taal/talen: Engels als bijlage per email.

De handleiding is 7,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info