809227
8
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
8
Using your boiler
Greenstar Heatslave II 2022+ – 6 721 843 979 (2022/01)
3.2.7 Frost protection
The boiler has built in frost protection to protect the boiler,
the boiler must have power for this to operate.
If you are leaving the property unoccupied during cold
weather, please leave your programmer on constant and
your room thermostat set to around 10 to 15°C.
If the temperature within the boiler falls below 8°C the
pump will run to circulate water and prevent the system
freezing.
If the temperature within the boiler falls below 4.5°C the
boiler will fire immediately, bringing the boiler temperature
up to 12°C to avoid the possibility of the system freezing.
This process will be repeated until such time that the boiler
temperature does not drop below 4.5°C.
3.2.8 System pressure
This boiler is fitted to a sealed heating system which is pre-
pressurised. Your installer will advise you of the minimum and
maximum pressure indicated on the pressure gauge.
Check regularly that the pressure is maintained.
Fig. 5
Optimum system pressure when your boiler is cold (area A) and
the pump is off. The indicated pressure will change as the pump
switches on, for more accurate readings check pressure when
the pump is not running.
If the pressure gauge reads less than 1 bar then the system
requires re-charging.
Check for leaks on heating system (pipe work and
radiator valves).
Contact your installer or maintenance engineer if a
permanent significant decrease or increase in pressure is
indicated on the pressure gauge.
Constantly having to re-pressuring the heating system
should be investigated as the concentration of inhibitor
in the system will be reduced; this can result in
corrosion within the heating system.
Filling loop
If the sealed system pressure within your system drops to
below 0.5 bar (shown on the pressure gauge) you will need to
increase the pressure to ensure your boiler continues to run
without problems.
Once the external filling loop has been located, follow the
instructions for re-pressurising the system.
1. Unscrew blanking cap.
2. Attach the hose to the valves, screw on hand-tight.
3. Turn the handle/screwdriver slot through 90° to open
valves.
4. The handle/screwdriver slot will be in line with the valves.
5. When the pressure reaches between the 1 and 1.5 bar
marks (zone A), turn the handles/screwdriver slots back,
through 90°, to close the valves.
6. The handle/screwdriver slot will be at 90° to the valves.
7. Remove the hose and replace the blanking caps.
Fig. 6
6 720 805 211-06.1TL
Your installer should have informed you where
to find the filling system and instructed you in
its use.
6 720 805 211-06.1TL
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worcester-Bosch Greenstar Heatslave II Internal bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worcester-Bosch Greenstar Heatslave II Internal in de taal/talen: Engels als bijlage per email.

De handleiding is 2.19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info