50963
31
Verklein
Vergroot
Pagina terug
1/53
Pagina verder
Digit 12 + = Weight value increases : speed of motion see digit 15
- = Weight value decreases
1 = Weight value no motion : base level < 0,2 division in 0,8 sec.
2 = Weight value no motion : high level < 0,1 division in 1,8 sec.
? = A “set zero” command is received but the zero function is disabled with switch 5.
This command will not be executed.
> = A “set zero” command is received (zero track incl.) that, if executed, will
exceed the zero setting range . This command will not be executed.
= = The auto zero at power on will exceed the initial zero limits (-5%. .+15%, in not
legal mode -20%. .+80%).
The zero setting will not be executed, the previous zero value is not deleted and
may be transmitted after the command: X ? Z .
This = sign ranks prior to all other reports in this digit.
This report will be deleted as soon as zero setting is possible or by the command
X ! E 6, see “ E “ commands on page 38.
< = A “set net” command (tare to zero) is received (auto tare in setpoint commands
too) but the gross weight value is negative. This command will not be executed,
and a setpoint start with tare included will be blocked . See digit 4 also.
Not executable zero and tare commands stay active until execution is possible, or
are deleted after the receipt of another command.
Digit 13 = Status of the setpoints, see table 6, page 44.
Digit 14 = Decimal point and scale division multiplication factor, as selected with
switch 53 t/m 56.
The multiplication factor is integrated already in the transmitted weight value.
However the position of the decimal point should be derived from digit 14, see
table 3 on page 41.
Digit 15 = Speed of the in- or decrease of the weight value in divisions per second
(0 . . 58 d/sec.). See table 9 on page 47.
Digit 16 = End of string code: Carriage Return.
9.2 DATA STRING: A / D VALUE REQUEST with:
digit: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
data: X # A + 2 . 0 0 0 . 0 0 0 S 2 CR
Function : With this special command the rough output of the A/D converter may be requested
for.
Neither zero, tare nor divisions multiplication factor is accounted in this figure.
This 21 bits value corresponds direct with the actual loadcell signal at the input.
That means that with a 2 mV/V signal on the input, the A/D value will be 2,000,000.
So this figure may be interpreted too as the real loadcell signal, expressed in mV/V,
with a accuracy of 1 nano Volt ( = 0,000.000.001 Volt)
Digit 3 : Code A identifies this string as the A/D value from a 348
Digit 4 t/m 13 : Measured value 21 bit
Digit 14, 15 : No motion level S 1 or (high) S 2
manual 348-2 V 3.1 Page 31 01-06-2007
X ? S @ CR
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Weightec 348 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Weightec 348 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Weightec 348

Weightec 348 Gebruiksaanwijzing - Nederlands - 49 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info