694510
20
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
20
GB
General
It is common practice for the dealer where you purchased your gas  replace to take also care of installing it and connecting it
to the gas mains. If this is not the case, please ensure that the installation is done by a certi ed installer. Connecting gas devices
by unquali ed persons is prohibited, in which case we cannot give any guarantee that your gas hearth is functioning properly.
Location of controls and receiver
To access the controls and the receiver, please take the
following steps;
grab hold of the side of the lower frame,
and carefully pull the frame toward you.
Here, you will  nd the gas control unit (Mertik GV60-M1
C5D3KL) and the receiver (Mertik GB60-R4AU).
Batteries (standard)
The batteries of the remote handset and the receiver
will last for about one year. We recommend that you use
alkaline batteries.
You need to replace them when the LED of the remote set
becomes dimmer and the word BATT appears in the display. The receiver will warn you if it’s batteries need to be exchanged.
You’ll hear, during ignition, a beep for 0.8 seconds followed by 0,2 seconds silence.
Replacing the batteries of the remote
Open the lid in the backside cover. Gently remove the 9V block battery and disconnect it from the contact holder. Avoid
pulling the cable. Connect the new battery, replace the set, and close the lid.
Replacing the batteries of the receiver
Carefully pull the entire receiver from the bottom of the stove. Slide open the cover and insert 4 new 1.5V batteries (type LR6
or AA). Please make sure to place the batteries in the receiver in the proper way. Then return the receiver to the stove.
Optional adapter
You can also choose to connect an adapter to the receiver (art. no. INK.3270). When using an adapter, you will no longer need
batteries and will have to remove them from the receiver. In the event of a power outage, you can still use the  replace by
inserting the batteries.
Setting the remote control handset (standard)
Once the batteries are placed, you need to set the electronic code (only when using it for the  rst time). Press the reset button
on the receiver until you hear 2 acoustic signs, and then release the reset button. Then press the small  ame button (2) within
20 seconds until you hear a long acoustic signal to con rm that the code has been set.
Setting the time
Press the big- ame button (1) and the small-
ame button (2) simultaneously, and the display
will show short  ashes to indicate that you are in
the set mode.
When in the set mode, press the big- ame button
(1) to set the hours, and press the small- ame
button (2) to set the minutes.
Wait or press the OFF button (3) to return to
manual control.
GV60-R4AU
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Wanders Larix bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Wanders Larix in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 6,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info