571834
20
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
20
failed. Possible cause: air in the pilot burner pipe.
Important: If the pilot ame has gone out you must wait at least 5 MINUTES before repeating the
above-mentioned steps.
Setting the height of the ames
• After igniting the burner, the height of the ames will automatically reach the maximum position.
• Press button continuously to lower the ames and to switch o the burner (putting the re out: STAND
BY”). Press button briey to gradually lower the ames.
• Press button to increase the ame height. Briey press button to gradually increase the ames.
Switching o the appliance
• Press button to lower the ames and to switch o the burner.
• Then press “OFF button to switch o the entire unit, including the pilot ame.
• If the appliance is not used for a longer period it is advisable that you turn o the gas valve in the gas pipe.
Important: if the pilot ame has gone out for whatever reason, you must wait at least 5 MINUTES
before lighting the pilot ame again.
Failure
If it looks as if the signals of the remote control are not properly received by the stove (receiver), it may be
caused by:
• Empty batteries: change the batteries.
• An electronic problem: solve it by pressing the RESET button on the receiver.
• If the appliance often switches o you should contact your installer.
Control (manual control)
If the batteries are due for replacement or if the receiver is defect, you can also operate the hearth by hand.
To do so, you need to disconnect the ignition (piezo) cable of the receiver and slide it gently onto the piezo
connection of the gas control block.
Lighting the re and putting it out
1. Open the gas stopcock which is mounted in the gas pipe leading to
the appliance.
2. Press “O I switch on the gas control block in the I position.
3. Turn motor switch on the gas control block all the way to the right.
The switch will make a ticking sound.
4. Turn operating switch on the gas control block in the MAN
position; an orice becomes visible.
5. Push the metal pin in the orice with something like a small pen. The
gas will now ow to the pilot.
6. While keeping the metal pin pressed in, press the (square) ignition
fuse (next to the O I switch) to ignite the pilot ame. Look through
the glass to see whether the pilot ame is burning.
7. If the pilot ame is burning, keep the metal pin pressed for another
10 seconds and then release it. If the pilot ame dies, wait for another
5 minutes before repeating the above steps.
8. Turn operation knob to the ON position.
9. Turn motor switch to the left to ignite the burner and to select the
height of the ames.
!
!
20

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Wanders-Balsa-100

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Wanders Balsa 100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Wanders Balsa 100 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 9,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info