484284

Wahl Tondeuse diverse types Handleiding

1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Middle
are aligned properly. (See Clipper Maintenance Instructions.)
10. During use, do not place or leave appliance where it may be damaged by an
animal or exposed to weather.
11. To disconnect, turn all controls to “OFF,” then remove plug from outlet.
12.
Turn all controls to “OFF” before attaching or detaching detail trimmer blades.
SAVE THESE INSTRUCTIONS
This Clipper Has Been Designed For Household Use Only
OIL
The blades of your new clipper should be oiled every
few haircuts. Place a few drops of Wahl Clipper Oil
on the teeth of the blades as well as at the back of
the blade . Use only the Wahl Clipper Oil included in
the pack. Do not use hair oil, grease or any oil mixed
with kerosene or any solvent.
POWER SCREW
Your clipper has a power screw and it has been
adjusted for peak efficiency before leaving the factory.
However, if voltage in your home is low, you may need to
readjust it. To adjust power, turn your clipper
“ON”
. Use the
end of the cleaning brush or a screwdriver to turn power
screw in a clockwise direction until you hear a noise. Then,
slowly turn power screw in a counterclockwise direction, just
until noise stops. This is the maximum power setting.
CORD
The cord should not be used to pull the clipper. Since freedom
of movement needs to be
maintained, care should be used to keep the cord untwisted and unobstructed.
If your clipper has a polarized plug: To reduce the risk of electric shock, this appliance
has a polarized plug (one blade is wider than the other). This plug fits in a polarized outlet only
one way. In the event the plug does not fit fully in the outlet, reverse the
plug. Do not change the plug in any way.
TAPER LEVER
The taper lever adds versatility to your clipper by allowing you to
gradually change the closeness of your cut. (Up position = closest
cut; Down position = longest cut) Should the blades become
jammed with hair, move the taper lever up and down several times.
This will help free up the blades.
LIMITED WARRANTY
(Valid in U.S.A. only)
If your Wahl product fails to operate satisfactorily within five (5) years from the date of original
purchase or receipt as a gift, Wahl will, at our option, repair or replace it and return it to you FREE
OF CHARGE.
DO NOT RETURN THIS PRODUCT TO STORE WHERE PURCHASED. PRODUCTS NEEDING REPAIR
UNDER THIS WARRANTY SHOULD BE RETURNED WITH POSTAGE PREPAID TO:
WAHL CLIPPER CORPORATION
ATTN: REPAIR DEPARTMENT
3001 LOCUST STREET
STERLING, ILLINOIS 61081
Include a note describing the defect and the date of original purchase or receipt as a gift (if in
warranty). Products out of warranty will be repaired at our standard repair charges.
This warranty is void and no repair or replacement will be made under this warranty or otherwise if:
1. The product is modified in any manner.
2. The product is repaired by anyone other than Wahl Clipper Corporation.
3. The product has been subject to unreasonable use.
This warranty gives you specific legal rights and you may also have other rights which may
vary
from state to state. No other written express warranty is given. Any implied warranty, including any
warranty of merchantability which may arise from purchase or use, is limited to the five-year period
provided in this express warranty. Some states may not allow such limitation, so it may not apply to
you. No responsibility is assumed for incidental or consequential damages of any type, or for the use
of unauthorized attachments. Some states may not allow the exclusion or limitation of incidental or
consequential damages, so the limitation or exclusion may not apply to you. Warranty valid in U.S.A.
only. Outside U.S.A., check with store for Wahl authorized distributor’s warranty.
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed,
including the points listed below. Read all instructions and safeguards before using.
DANGER —
To reduce the risk of injury or death by electric shock:
1. Do not reach for an appliance that has fallen into water. Unplug immediately.
Some electrical parts inside the clipper are electrically live, even with the switch
“OFF.”
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall or be pulled into a tub or sink.
Do not place in or drop into water or other liquid.
4. Always unplug this appliance from the electrical outlet immediately after using.
5. Unplug this appliance before cleaning.
WARNING —
To reduce the risk of burns, fire, electric shock or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. Close supervision is necessary when this appliance is used by, on, or near
children or invalids.
3. Use this appliance only for its intended use, as described in this manual. Do
not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not
working properly, if it has been dropped or damaged, or dropped into water.
Return the appliance to Wahl Clipper Corporation for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never operate the appliance with the air openings blocked or while on a soft
combustible surface, such as a bed or couch, where air openings may be
blocked. Keep the air openings (if any) free from lint, hair or the like.
7. Never drop or insert any object into any opening on this appliance.
8. Do not use outdoors or operate with aerosol (spray) products or where oxygen
is being administered.
9. Do not use this appliance with a damaged or broken comb nor with teeth
missing from the blades, as injury may occur. Before use, make certain blades
Please register your Wahl Clipper online at: www.wahlhaircuts.com
Purchase Confirmation-
With the information your provide, we confirm the date of purchase of your product. This
confirmation is of benefit to you, especially if your original proof of purchase is lost.
Proof of Ownership-
Your UPC number, item number and other information will be kept in our files for up to ten years.
For personal attention from one of our customer service representitives please contact us at:
www.wahlhaircuts.com or 1-800-767-9245
© 2010 WAHL CLIPPER CORPORATION
P.O. Box 578, Sterling, Illinois 61081 USA
Part #94601-303
CLIPPER MAINTENANCE
Taper Lever
(Multi-Cut [MC] Clipper Only)
Top Blade
Bottom
Blade
Switch
Power Screw
ALIgNINg CLIPPER bLADES
Your Wahl clipper blades were oiled and aligned before leaving our factory. Blades may need
to be realigned if they have been bumped or removed for cleaning. To determine if realignment
is necessary, compare your clipper blades with this sketch.
1. If your clipper has a taper lever, position the lever in the close cut position.
2. End of top blade teeth should be approximately 1/32-inch (.64 mm) back from bottom blade.
3. Extreme left-hand tooth of top blade must be covering or to the left of the first small tooth
of bottom blade.
4. Extreme right-hand tooth of top blade must be touching the big tooth on the bottom blade.
If blade alignment is incorrect, add a few drops of Wahl Clipper Oil to the blades, turn clipper
“ON” for a few moments, turn “OFF” and unplug. Loosen screws slightly and adjust. Tighten
screws after blades are aligned. Other than blades, this clipper has no user-serviceable parts.
1. Comb hair and
remove tangles. Attach
the largest guide comb
to the clipper. Make sure
the taper lever is in the
up position.
2. Start at hairline on
side of head and cut
up to middle of head.
Note: If cut hair is
too long repeat with
next smaller guide
comb.
3. Continue around
head repeating step 2.
4. You are now ready to
cut the middle portion of
the hair.
5. Select the proper guide
comb. Use the comb with
the next highest number
than in step 3. Example:
If you used a #6 comb in
step 3, select comb #7.
6. Continue cutting
around middle portion of
head as in steps 2 and 3.
7. For cutting top of
head, use the comb with
the next highest number
than in step 6.
Start at front bang area.
8. Cut across top of
head.
9. Comb hair on entire
head to assess if further
cutting is necessary.
10. Blend out any cut
lines. Lines may form
where you change comb
sizes. Use the same
comb used in step 3
with taper lever in down
position.
12. Using the comb used in
step 8 repeat blending the
top outline as in step 10.
O U T L I N I N G
T A P E R I N G
1. The ear guide combs
have a built in taper
ranging from 1/8” to 1/2”.
2. Attach the left ear
guide comb to the
clipper. Put taper lever in
down position.
3. Hold the clipper at a
slight angle just back of
the ear at the hairline.
Hold top of ear down.
4. Move the clipper
upward and around
the ear.
Repeat the same for the
right ear with the right
ear guide comb.
1. Select the guide comb
for the desired length
hair. Attach to clipper
with the taper lever in
the up position.
2. Hold the clipper flat
against the neck and
slowly move the clipper
through the hair as
shown.
3. Use the same procedure
from the lower side of the
head to the upper side of
the head.
C R E W C U T S
B L E N D I N G
For more information or product
registration, visit wahlhaircuts.com
1. Attach the brow trim guide to clipper
2. Starting from just above your nose, slowly guide
the clipper to the outside of your face.
For shorter brow trim repeat steps 1 and 2
working from outside face to your nose.
1. Attach ear trim guide to clipper.
2. Hold the clipper at a 45-degree angle.
3. Slowly move the clipper from back to front.
Avoid poking eyes.
B R O W T R I m G U I D E E A R T R I m G U I D E
1. No attachments
needed. Push the taper
lever up to the close cut
position.
2. Start with the
sideburns.
3. Continue around ear
as shown.
ATTACHING GUIDE COMBS
Align comb onto blade then press
tab until you hear a snap.
C U T T I N G H A I R
11. Using a rocking
motion, blend out the
middle cut line.
4. Cut the top using a
guide comb two sizes
(lengths) longer than the
comb used on sides. Start
at the front and cut slowly
to the back as shown.
4. Trim neckline as
shown.
5. Around the ears.
guIDE COMb LISTINg
Some kits do not include all Wahl guide combs. Some kits include colored
guide combs for ease in remembering which combs were previously used.
#
1
/2
-
(1.5mm)
1
/16”
Light Green/Black
#
1
-
(3mm)
1
/8”
Red/Black
#
1
1
/2
-
(4.5mm)
3
/16”
Burgundy/Black
#
2
-
(6mm)
1
/4”
Purple/Black
#
3
-
(10mm)
3
/8”
Dark Blue/Black
#
4
-
(13mm)
1
/2”
Orange/Black
#
5
-
(16mm)
5
/8”
Yellow/Black
#
6
-
(19mm)
3
/4”
Lavender/Black
#
7
-
(22mm)
7
/8”
Green/Black
#
8
-
(25mm) 1”
Light Blue/Black
#
12
-
(38mm) 1
1
/2
”
Black Only
#
10
-
(31mm) 1
1
/4
”
White Only
NOTE:
1) Always start with the largest guide
comb, then use shorter combs if a
shorter length is desired.
2) Cut only a small amount until you
become accustomed to how long
each guide comb leaves the hair.
3) Cut slowly and smoothly. Do not
force the clipper through the hair.
Home
Haircutting
witH
ActuAl BlAde Size
NOTE:
NOT ALL WAHL KITS
INCLUDE BROW OR
EAR TRIM GUIDE
The first time you cut hair, cut only
a small amount of hair until you
become accustomed to the length
of hair each guide comb provides.
• Start by attaching the largest
guide comb on the clipper.
• Then use shorter combs if a
shorter length is desired.
• For uniform cutting, cut at a
slow even speed.
1
ST
TImE
CUTTING HAIR
1

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Wahl-Tondeuse-diverse-types

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Wahl Tondeuse diverse types bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Wahl Tondeuse diverse types in de taal/talen: Engels als bijlage per email.

De handleiding is 2,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Wahl Tondeuse diverse types

Wahl Tondeuse diverse types Aanvulling / aanpassing - English - 1 pagina's

Wahl Tondeuse diverse types Gebruiksaanwijzing - English - 4 pagina's

Wahl Tondeuse diverse types Aanvulling / aanpassing - English - 4 pagina's

Wahl Tondeuse diverse types Gebruiksaanwijzing - English - 2 pagina's

Wahl Tondeuse diverse types Gebruiksaanwijzing - English - 2 pagina's

Wahl Tondeuse diverse types Gebruiksaanwijzing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info