667318
49
Verklein
Vergroot
Pagina terug
1/234
Pagina verder
47
DEFRNLITESPTPLHURU EN
0478 111 9925 B - EN
11.8 Sharpening the mowing blade
If mowing results deteriorate over time,
this is usually the result of a blunt mowing
blade.
The following points must be noted when
resharpening:
Remove the mowing blade. (Ö 11.7)
Cool the mowing blade when
sharpening, e.g. with water. The blade
must not be allowed to display blue
colouring, as this would reduce its
cutting quality.
Sharpen blades evenly to prevent
vibration due to imbalance.
The cutting angle of 30° must be
observed.
Observe the wear limits when
sharpening.
Remove any sharpening burr.
11.9 Maintaining cables
The cables are adjusted correctly at the
factory.
The throttle cable and the blade brake
clutch cable must only be maintained by
trained personnel. VIKING recommends
VIKING specialist dealers.
After prolonged use or under certain
conditions, it can be necessary to adjust
the self-propulsion cables.
Adjusting the hydro self-
propulsion cable
MB 756.0 YS, MB 756.0 YC
Maintenance interval:
As required
Adjustment of the cable can be necessary
if the maximum driving speed is no
longer achieved over time.
if self-propulsion is permanently
engaged. This means that the lawn
mower automatically begins to move
when the recoil starter rope is pulled,
despite the self-propulsion lever not
being actuated.
Adjusting the cable
1 Push driving speed lever (1)
fully forwards.
2 Loosen lock nut (2), loosen
shift linking (3) by turning adjustment
nuts (4).
3 Adjust cable (5) using the two
nuts (6, 7).
When correctly adjusted, the cable is
tensioned slightly and pin (8) is
positioned right at the bottom of
guide (9). The machine can be pulled
back – the wheels are not blocked
during this process.
4 Adjust the shift linkage without play
using adjustment nuts (4), then tighten
lock nut (2) again.
Adjusting the gearshift cable
MB 756.0 GS
Maintenance interval:
As required
Adjustment of the cable is necessary
if, following lengthy use, the individual
gears can no longer be engaged.
Adjusting the cable
Tension cable (1) using the two
nuts (2, 3) on the underside of the
handlebar so that all three gears can be
correctly engaged.
Adjusting the self-propulsion
cable
MB 756.0 GS
Maintenance interval:
As required
Adjustment of the cable is necessary
if, after a lengthy period of use, self-
propulsion does not engage when the
self-propulsion lever is actuated.
if self-propulsion is permanently
engaged. This means that the lawn
mower automatically begins to move
when the recoil starter rope is pulled,
despite the self-propulsion lever not
being actuated.
Checking the cable tension:
1. Engage 3rd gear and pull the recoil
starter rope – the lawn mower is not
driven.
2. Pull the self-propulsion lever to the
handlebar and hold, pull the recoil
starter rope - the lawn mower is driven.
Risk of injury!
The prescribed tightening torque
must be observed.
Retaining washer (3) must be
replaced each time the blade is
installed.
Blade fastening screw (2) must be
renewed each time the blade is
replaced.
22
23
Risk of injury!
The self-propulsion cable must be
correctly adjusted before the
machine is operated.
24
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Viking MB 756 YS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Viking MB 756 YS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 13,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info