667349
45
Verklein
Vergroot
Pagina terug
1/548
Pagina verder
43
DEFRNLITESPTNOSVFIDAPLSLSKHU EN
0478 201 9906 D - EN
Never spray water onto
motor or engine components,
seals, bearing points or
electrical parts such as
switches. This would result in
expensive repairs.
If you are unable to remove
the dirt and accumulated
deposits with a brush, a damp
cloth or a stick, VIKING
recommends the use of a
special cleaner (e.g. STIHL
special cleaner).
Do not use aggressive cleaning agents.
Clean the blade discs regularly.
11.2 Installing the feed chute
Attach feed chute (1) to fastening hooks
on the basic unit (2) and pivot forwards.
Tighten both closure screws (3)
simultaneously.
11.3 Removing the feed chute
Loosen both closure screws (1)
until they turn freely. They remain
on the feed chute
Pivot the feed chute (2) to the rear and
remove.
11.4 Locking the blade disc
Remove the feed chute. (Ö 11.3)
Turn blade disc (1) to that the
recess (2) is located in front of the
locking device (3).
Fold up the locking device (3).
11.5 Removing the blade set
Lock the blade disc (5). (Ö 11.4)
Loosen screw (1) with
combination spanner (V).
Remove the screw (1), retaining
washer (2), clamping ring (3), wing
blade (4), wing blade (6, only on
GE 250 and GE 260) and blade
disc (5).
Remove the reversible blade. (Ö 11.8)
GE 250 and GE 260: Unscrew
screws (7) and remove together with
nuts (9). Remove the shredding
blades (8) downwards.
11.6 Installing the blade set
Attach the reversible blade to the blade
disc. (Ö 11.7)
GE 250 and GE 260: Position the
shredding blades (8) on the underside
of the blade disc (5) and fasten with
nuts (9) and screws (7) (10 Nm).
Insert the blade disc (5) into the
housing and fasten. (Ö 11.4)
Fit the wing blade (6, for GE 250 and
GE 260 only), wing blade (4), clamping
ring (3) and retaining washer (2) and
fasten with screw (1) (50 Nm).
Fold back the locking device so that the
blade disc can turn freely again.
(Ö 11.4)
Install the feed chute. (Ö 11.2)
11.7 Blade maintenance
Maintenance interval:
Before each use
Remove the feed chute. (Ö 11.3)
Lock the blade disc. (Ö 11.4)
Check the blades for damage (notches
or cracks) and wear; reverse or replace
if necessary.
Wear limits of the blades:
The closure screws must be
securely fastened to the feed chute.
14
15
Risk of injury:
Always wear gloves.
Do not touch the blades
until they have come to a
standstill.
The installation sequence and
specified tightening torques must
always be observed.
16
17
17
Risk of injury!
Always wear thick
gloves.
The blades must be reversed or
replaced before the specified wear
limits are reached. VIKING
recommends VIKING specialist
dealers.
18
45

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Viking-GE-150

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Viking GE 150 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Viking GE 150 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 18,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info