785222
35
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
BMS
Check BMS functionality by deliberately loosening a BMS cable
10.3.7. System in sleep or hibernate mode
This is indicated by the status LED off and the Bluetooth LED flashing every 3 seconds.
The Lynx Smart BMS goes into sleep or hibernation mode once the battery or a battery cell has been deeply discharged. The
Lynx Smart BMS will conserve as much power as possible, to not discharge the battery much further and will switch the Bluetooth
module and other non-essential internal circuits off.
Check the voltages of the connected batteries and if they are low, charge the batteries. As soon as the Lynx Smart BMS sees a
charge voltage it will automatically re-activate and close its contactor to allow for battery charging.
10.3.8. Battery communication error
This is indicated by the red LED flashing 2 times every 4 seconds or with the GX device BMS cable error. A battery
communication error occurs when the Lynx Smart BMS is not connected to the battery BMS communication cables, or if there is
an issue with the BMS cables. To remedy this error, check the following:
Check if both battery cables are connected to the Lynx Smart BMS.
In case of a multiple battery setup , check if all batteries are interconnected
Check for loose connections, the male connector needs to screw “hand tight” into the female connector.
10.4. Battery monitor issues
10.4.1. Incomplete current reading
The negatives of all the loads and the charge sources in the system must be connected to the system minus side of the Lynx
Smart BMS.
If the negative of a load or a charge source is connected directly to the negative battery terminal or the “battery minus” side on the
Lynx Smart BMS, their current will not flow through the battery monitor and will be excluded from the overall current reading and
the state of charge reading.
The SmartShunt will display a higher state of charge than the actual state of charge of the battery.
Lynx Smart BMS
Page 32 Troubleshooting and Support
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron Lynx Smart BMS 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron Lynx Smart BMS 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 3.23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info