785222
10
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
4. Communication and interfacing
4.1. The VictronConnect App
The VictronConnect App communicates via Bluetooth. It is used for changing settings, monitoring the Lynx Smart BMS and up to
4 connected Lynx Distributors. For more information on the VictronConnect App see the VictronConnect manual.
4.2. GX Device and the VRM Portal
The Lynx Smart BMS can be connected to a GX device via VE.Can and the GX device in its turn can communicate with the VRM
portal. The GX device and the VRM will show all measured parameters, operational state, battery SoC and alarms.
4.3. Communication Lynx Distributor
Up to 4 Lynx Distributors can be connected to a Lynx Smart BMS. They communicate via the RJ11 cable. The Lynx Distributors
communicate fuse status and operational status to the Lynx Smart BMS. The Lynx Smart BMS can be used to read out the Lynx
Distributors, generate alarms in case a fuse is blown or communication is lost.
4.4. DVCC
DVCC allows the Lynx Smart BMS to control Victron Energy inverter/chargers, AC chargers and solar chargers via a GX device.
The Lynx Smart BMS will automatically adjust discharge current, charge current and charge voltage depending on the battery
state. For the action taken for each battery state, see below table.
DVCC is automatically activated. The following parameters are implemented:
Fixed parameters:
Absorption voltage is set at 14.2V
Storage/float voltage is set at 13.5V
Max charge current is set at 1C
Charge current at low cell voltage is set at 0.1C
User configurable via the VictronConnect app:
Absorption time
State of charge (SoC) threshold (A new charge cycle will be initiated as soon and the the battery state of charge drops below
this threshold)
Repeated absorption time (The number of days after which a new charge cycle is initiated, even though the battery state of
charge is still above the state of charge threshold)
For more information on DVCC and to find out which Victron Energy products can be controlled via DVCC, see the GX device
manual.
Table 1. DVCC action taken when certain battery conditions occur
Battery condition Allowed to
discharge
signal
Allowed
to charge
signal
DVCC action
A battery cell voltage is below
5°C.
This is a low temperature alarm.
High Low The charge current is reduced by lowering the charge
voltage to battery voltage minus 0.15V. This will
reduce the charge current to 0A.
The battery is signalling a low
voltage pre-alarm.
High High This is user selectable. Can be set to reduce the
discharge current to 0A, or to take no action.
A battery cell voltage is too low.
This is a under-voltage alarm
Low High The discharge current is reduced to 0A. Once the
under-voltage alarm is cleared it will be set back to
600A.
The charge voltage is reduced until the charge current
is 0.1C. Once the under-voltage alarm is cleared the
charge voltage will go back to 14.2V (28.4V).
Lynx Smart BMS
Page 7 Communication and interfacing
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron Lynx Smart BMS 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron Lynx Smart BMS 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 3.23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info