785236
54
Verklein
Vergroot
Pagina terug
1/59
Pagina verder
In more detail, there are several causes for measurement inaccuracies:
1. Part of the power taken from a battery by the inverter is being lost in the inverter, converted into heat: efficiency losses.
2. The Multi does not really measure the power being drawn from the battery. It measures the current at the output of the inver-
ter, and then makes an assumption of the power being drawn from the battery.
3. Watts vs VA: depending on the Multi/Quattro firmware version and also the Cerbo GX firmware version, you are either looking
at VAs (the result of calculating AC voltage * AC current) or looking at a Watts measurement. To see WATTS on the Cerbo
GX, update your Cerbo GX to the latest version (v1.21 or newer). Also make sure the firmware version in your Multi supports
Watts readout, minimum versions are xxxx154, xxxx205 and xxxx300.
4. Multis/Quattros connected to the Cerbo GX via a VE.Bus to VE.Can interface will always reports VAs, not (yet) Watts.
5. If a current sensor assistant is loaded in a Multi/Quattro and no sensor is connected it will return invalid power / kWh values.
6. If a current sensor assistant is loaded in a Multi/Quattro make sure the position is set correctly and the scale match with the
dipswitches on the sensor itself.
7. A current sensor assistant measures and reports VAs, not Watts.
Notes for systems with multiple units in parallel:
1. Cerbo GX version prior to v1.20 use the power and current reported by the master of a phase and multiplied that by the num-
ber of devices in that phase. Since version v1.20 the values of all device is summed per phase and hence should be more
accurate.
2. This revealed a bug for in the firmware of the multi when running in parallel. Ccgx v1.21 workarounds this, by falling back to
the original behavior when it sees an affected firmware version. For better readings the multi's should be updated. The bug
has been fixed in VE.Bus firmware version xxxx159, xxxx209, xxxx306. That firmware was released on February 17th 2015.
3. Multi firmware versions since 26xx207 / xxxx300 can also freeze the Power values at a certain moment in time.
Tips to prevent measurement problems:
1. Do not connect VEConfigure while the Cerbo GX is connected
2. VE.Bus is not a 100% plug and play system: if you disconnect the Cerbo GX from one Multi, and very quickly connect it to
another, it can result it wrong values. To make sure that this is not the case, use the 'redetect system' option in the Multi/
Quattro menu on the Cerbo GX.
13.7. Q7: There is a menu entry named "Multi" instead of the VE.Bus product
name
A VE.Bus system can be completely turned off, including its communication. If you turn a VE.Bus system off, and thereafter reset
the Cerbo GX, the Cerbo GX cannot obtain the detailed product name and shows “Multi” instead.
To get the proper name again, go into the Multi menu on the Cerbo GX and set the Switch menu entry to On or in case a Digital
Multi Control is present, set the physical switch to On. Note that when there is a BMS, above procedure only works when within
battery working voltages.
13.8. Q8: There is a menu entry named "Multi", while there is no Inverter, Multi
or Quattro connected
If a Cerbo GX ever saw a VE.Bus BMS or Digital Multi Control (DMC), it will remember them, until 'Redetect system' is started
from the Cerbo GX menu.After a minute, restart the Cerbo GX: Settings → General → Reboot.
13.9. Q9: When I type the ip-address of the Color Control into my browser, I see
a web page mentioning Hiawatha?
Our plan is to at least run a website where you can change settings and see the current status. If all works out as we would like
to, there might come be a fully functional version of the online VRM Portal running locally on the Cerbo GX. This allows people
without an internet connection, or an intermittent internet connection to have the same features and functionality.
13.10. Q10: I have multiple Solar chargers MPPT 150/70 running in parallel. From
which one will I see the relay status in the Cerbo GX menu?
From a random one.
13.11. Q11: How long should an automatic update take?
The size of the download typically is around 90MB. After download it will install the files which can take up to 5 minutes.
13.12. Q12: I have a VGR with IO Extender, how can I replace this with a Cerbo
GX?
It is not yet possible to replace the IO Extender functionality.
13.13. Q13: Can I use Remote VEConfigure, as I was doing with the VGR2?
Yes, see VE Power Setup manual
Cerbo GX Manual
54
54

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron Cebro GX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron Cebro GX in de taal/talen: Engels als bijlage per email.

De handleiding is 5.1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info