783524
35
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
31
4) Tip the machine on its back and remove the two, small Phillips head screws on the bottom of the machine along
the back edge of the bottom. Stand the machine back on its feet
5) Remove the 6 screws on the outer case (three on each side). Slide the outer case off the machine
6) Replace the water reservoirs platform and the reservoir and replace the hoses back into the reservoir.
7) Pour the de-scaling agent into the water reservoir. You will need to fill it at least 1/2 full. Be sure to follow the
manufacturers recommendations as to the mixing of the de-scaler to the proper concentration.
8) Plug the machine in and turn the power switch to Position I only! Allow the boiler to fill. Continue to the next
step after the pump stops.
WARNING: In many of the following steps, such as when pumping the de-scaler through the group-
head and removing the hoses from the water tank, splashing acid can create a safety hazard. Gloves, eye
protection, and protection for the working surface are required.
9) Place a suitable container under the grouphead and turn on the brew function to run about eight ounces out of
the machine to get the de-scaling agent through the grouphead. This also ensures that the thermosyphon pipes,
the inside of the heat exchanger and internal portions of the grouphead get de-scaled.
CAUTION: If the used de-scaling agent is poured down a drain, allow the faucet to run into the sink
to dilute the acid. Never re-use the spent acid.
10) Snap the blind filter into the portafilter handle and backflush the machine. Turn on the brew function and
allow it to run for about five seconds. This will force the de-scaler through the over pressure relief valve. You
will see the liquid flowing back into the reservoir through the secondary hose. When that takes place, turn the
machine to “0” and unplug the power cord. Leave the hoses in place and move the reservoir off to the side of
the machine and lift off the reservoir platform.
11) Remove the two Phillips head screws holding the top of the divider panel and swing it back and off the ma-
chine. Take care not to stress the wires attached to the water-level microswitch which is attached to the panel.
12) Remove the water level sensor wire by loosening the screw indicated in these two photos. Leave it discon-
nected for now. This will fool the boiler into thinking that the boiler is low on water and needs to be refilled.
Set the wire off to the side where it cannot accidently
connect with any metal parts.
13) Replace the divider panel and reinstall the two Phil-
lips head screws holding the top of the divider panel
in place. Reinstall the reservoir platform and reservoir
and insert the hoses once again. If needed, refill the res-
ervoir with de-scaling agent.
14) With the autofill wire still disconnected, plug the
machine back in, remove the tip and O-ring from the
steam wand and place them off to the side. Place a suit-
able container under the steam wand and the hot water
wand and open the steam valve.
15) Turn the power switch to position “I” only. The au-
tofill is defeated and so the machine will overfill (com-
pletely fill) the boiler. As soon as a solid stream comes
out of the steam wand, turn the power switch to Position
0 and close the steam valve.
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vibiemme Domobar Super bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vibiemme Domobar Super in de taal/talen: Engels als bijlage per email.

De handleiding is 4.39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info