514914
3
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
VERMEIREN
DX2 Basic: without LCDscreen
DX2 with LCD screen
I N S T R U C T I O N M A N U A L
DX2 Operator control
vD - 2013-04
1
OPERATOR CONTROL DX2
1. Use
The operator control built into your electric wheelchair enables you to control all the driving,
steering, braking and operating processes and to control other adjusting motors (lifting
column, seat and back adjuster). The wheelchair's electrical unit and electronics are
constantly being monitored internally. Any fault in the electronics is indicated on the
operating display (6) and the status display (1) and, if necessary, the wheelchair may be
switched off for reasons of safety (see the chapter on fault analysis).
Vermeiren is responsible for the changes in the software. For changes in the software
contact Vermeiren.
The DX2 system is available in two different operator controls (DX2 Basic; DX2 with LCD
screen) which have some different operating buttons.
1
2
3
4
5
6
7
8
9
10
1 = Display
2 = "ON / OFF" button
3 = "Left indicator" + "Light" button
4 = "Right indicator" + "Warning
indicator" button
5 = "Horn" button
6 = Fault code/operating display
7 = Brightness sensor
8 = "Drive profile" button
9 = "Select field" button
10 = Max speed reduction
With LCD screen
1 = "ON / OFF" button
2 = Battery charge
indicator
3 = Speed switch
"-" : slower
"+" : faster
4 = Speed indicator
5 = "Horn" button
6 = Light sensor*
7 = Lock Led
8 = Left indicator
9 = Right indicator
10 = Left indicator LED
11 = Right indicator LED
12 = Adjustment Actuator LEDs
13 = Adjustment Actuator
selection
"-": down
"+": up
14 = Warning indicator
15 = Lights
16 = Attendant profile LED
17 = Fault indicator LED
18 = LED side lights
DX2 Basic:
Without LCD
screen
* The light sensor dims the display when it is dark
2
1
10
3
4
5
6
8
14
16
17
18
15
13
12
9
7
11
DX2 Operator control
vD - 2013-04
2
1.1. DX2 without LCD screen
Press the "ON/OFF" button (1). The charge indicator (2), which also indicates the batteries' charge
level, lights up for a moment. If all the lights come on, the batteries are sufficiently charged. If the lights
do not all come on, you must adjust your driving activities to suit the low capacity of the batteries. If the
battery charger display lights do not come on, check the plug connections of the electronic system.
Now select the driving program you want by pressing the speed switch (3), (-) symbol to go slower and
(+) symbol to go faster.
The selected speed is showed with the speed indicator (4). If you have any special needs, you can
ask your dealer to enter a personalised driving program.
To set the wheelchair in motion, push the joystick forwards slowly. The speed will increase when you
push the joystick further forwards. If you want to turn left or right, simply push the joystick in the
desired direction. To reverse, pull the joystick backwards from the central position.
L
Note that, when pressing the "ON/OFF" button, the joystick stays in the central position for at
least two seconds. It is programmed this way for technical and safety reasons, to prevent the
joystick being pushed at the same time as the wheelchair is being switched on. If both
processes are activated at the same time, the steering unit locks itself and can only become
operational again after being switched off completely.
Press the “Left indicator” (10) or “Right indicator” (11) buttons to signal a change in your driving
direction. The driving lights are switched on or off by pressing the “Lights” (15) button. You can sound
an acoustic warning signal with the “Horn” (5) button. The hazard warning lights, used in critical
situations, can be switched on or off by pressing the “Hazard warning lights” (14) button.
To brake while driving, simply push the joystick to its central position. Move the joystick slowly for
gradual braking. Simply release the lever for a quick stop; the wheelchair will then stop as quickly as
possible.
To activate the back adjuster, select button (13) until the corresponding number for the backrest
adjustment actuator lights up, and you can then use the joystick to tilt the back in the direction you
want.
To activate the seat incliner, select button (13) until the corresponding number for the seat adjustment
actuator lights up, and you can then use the joystick to incline the seat in the direction you want.
Turn wheelchair On/Off
In case of an emergency, you can use the On/off button to turn your wheelchair off.
Turn the power on:
Press the On/Off button. All LEDs of the battery indicator turn on simultaneously
and the fault indicator flash twice.
If the wheelchair is turned on while the joystick is out of neutral, an fault will be displayed on the
battery charge indicator (the five drive profile LEDs flash continuously and the chair will not drive).
Release the joystick back to neutral and the fault will disappear. If the joystick is not released
back to neutral (centre) within 4 seconds, the fault becomes a Module fault (the drive profile LEDs
+ fault indicator are flashing). To clear this fault, turn the DX system off and then turn it back on.
Turn the power off:
Press the On/Off button. All LED's will goe out. If the ON/OFF button is pressed
while driving the wheelchair perform an emergency stop and it turns off.
DX2 Operator control
vD - 2013-04
3
Locking your operator control
It is possible to lock your operator control so that unauthorized people cannot turn your electric
wheelchair on.
To lock your wheelchair:
While the power is ON, press and hold the ON/OFF button for 4 seconds.
The display will turn off immediately. After 4 seconds all LED's and the Lock LED
turn on for 1 second to indicate that the DX system is now locked.
To unlock your wheelchair:
While your wheelchair is locked, press the ON/OFF button to turn your
wheelchair on.
The Lock LED will flash for 10 seconds to indicate that the DX system is locked.
Press the Horn button twice before the countdown is completed (approximately
10 seconds).
The current state-of-charge will then be displayed and the operator control may
be operated normally.
If the user does not press the Horn button twice before the countdown is complete, the
Horn will sound a short beep and your operator control will turn itself off.
You must complete these procedure completely otherwise your wheelchair will not drive
again.
Sleep mode
The DX System will go to sleep after a period of inactivity of a quarter.
When the DX System sleeps, it is partially turned off to reduce energy consumption.
To reactivate the DX system:
Press any button on the DX system or move the joystick. The DX system turns
on.
DX2 Operator control
vD - 2013-04
4
Using battery charge indicator
The battery charge indicator is used to indicate that your wheelchair power is on
and provides an estimate of the remaining battery capacity.
Any green LED's indicate that your batteries are well charged.
If only amber and red LED's are light, the batteries are moderately charged.
Recharge your batteries before you make a long trip.
If only red LED's are light, the batteries are running out of charge. Recharge as
soon as possible.
The following table indicates what the battery charge indicator will display.
Display Description Meaning Remarks
All LEDs dark. System off.
All LEDs are
flashing.
System on. Warning: battery too full.
Slow down if you are
driving down a slope.
All LEDs are lit. System on. LEDs show the charge
level.: Full battery
Only red and yellow
LEDs lit.
Low battery level. Battery half full. Start the
return journey.
Only red LEDs lit. Very low battery level. Battery low. Recharge
soon.
Red LEDs are
flashing.
Battery almost empty. Recharge now.
1 Red Led is
flashing.
Battery empty. Recharge immediately.
The LEDs turn on
one by one from left
to right.
Drive inhibit, the chair will
not drive.
The LEDs turn on
one by one from left
to right, followed by
one second where
the current battery
capacity is
displayed.
The charger is connected to
the operator control.
All leds turn on one
by one from left to
right. The Fault
indicator will show
corresponding flash
code.
Indicate that the chair will
not drive.
A fault has occurred.
DX2 Operator control
vD - 2013-04
5
Adjusting the Driving Speed
The DX2 system without LCD screen support 5 drive
profiles. A drive profile is a specific drive setting (slow
or fast, indoors or outdoors) that your therapist or
dealer can adjust to suit your personal needs and
preference. You can select the active Drive Profile
with the Drive Profile Selection button.
Press ‘+’ to increase the drive speed/profile.
Press ‘-‘ to decrease the drive speed/profile.
Using the drive profile indicator
Select a Drive Profile that suits your preference and environment. The currently selected Drive
profile is indicated with the speed indicator LED’s.
LEDs Meaning
Drive Profile 1.
Drive Profile 2.
Drive Profile 3
Drive Profile 4
Drive Profile 5
Attendant Control
When the attendant control is activated, the ACU LED will light up and remain
light until the attendant relinquishes control.
In these mode the DX joystick does not work and it is not possible to select a
different drive profile. All the other buttons works.
Using the horn
Press the horn button. The horn shall sound as long as the button is pressed.
DX2 Operator control
vD - 2013-04
6
The Service indicator light
The Service indicator LED is dedicated to displaying fault codes. For a list of
the fault codes refer to paragraph 2.
If the electric wheelchair has exceeded the drive time and needs maintenance,
the fault indicator LED turns on continously for 15 seconds every time the
system is turned on. Take your wheelchair to a qualified service center for
maintenance.
Using the lights
Headlights:
To turn the Headlights on, press the Headlight Button. The green
Headlight LED next to button will lit. Press the Headlight Button
again to turn the headlights off.
Left and Right indicator lights:
To indicate left or right turns, press the Left or Right Indicator Button
as required. The green activated Light Indicator LED will flash. Press
the Button again to turn the indicator off.
Hazard warning lights:
To turn the Hazard lights on, press the Hazard Button. The two
green Left and Right Indicator LEDs will both flash simultaneously.
Press the Hazard button again to turn the hazard function off.
Using the seating function Button
When you have placed the DX system in the seating mode the
joystick does not drive the wheelchair, it only selects and operates
the seating functions.
Press the ‘+’ or the ‘-‘ on the seat function button to activate the
seating mode. The seating mode starts with the seating function
that was last selected. The seat function LEDs indicate the
currently selected seating function.
Selecting the correct seat function (adjustment seat, backrest, legrests, …).
Press ‘+’ or move the joystick right to select the next seating function.
Press ‘-’ or move the joystick left to select the previous seating function.
Buttons
LEDs
DX2 Operator control
vD - 2013-04
7
Operating the seating functions (adjustment seat, backrest, legrests, …).
Move the joystick forward to operate the seating function in one direction. Move the joystick
backwards to operate the seating function in the opposite direction.
The active seating function LED flashes while operating the actuator. If you move the joystick
further forward, the seating function moves faster.
Return to the driving mode
Press the ‘+’ or the ‘-‘ on the drive profile selection button to return to the
driving mode.
The Driving mode returns to the drive profile that was selected before the
seating mode was activated.
Available seating functions
The DX2 basic system can operate in 4 seating functions or 4 seating functions and one
combined function (ex. 2 footrests together).
Actuator Function LEDs Meaning
Seating Function 1 selected
Seating Function 2 selected
Seating Function 3 selected
Seating Function 4 selected
Seating Function 3 and 4 selected
Using the Joystick
Moving the joystick will drive the electric wheelchair in that direction. The
amount of joystick movement will determine the speed that the powerchair will
move in that direction.
Make sure that the joystick is in the neutral (central) position when pressing the
on/off button, otherwise the electronics will be locked. To take this block away
let go the joystick until he goes back in neutral position.
DX2 Operator control
vD - 2013-04
8
1.2. DX2 with LCD screen
The function buttons (8), (9) and (10)
enable functions to be selected that
are displayed in the assigned fields on
the screen.
The status display is constantly visible
in the upper part of the display and
always shows the batteries' charge
level and the current time.
The light, indicator and warning light
displays only appear when the
relevant function is selected. The
system status display appears when
there is a fault or an event, and
displays the relevant event or fault
code (1-12).
Display Meaning
Battery fully charged
Battery fully charged
Battery half charged
Battery will soon be low, charge
it
Battery is low, charge it soon
Battery is dead, charge now
Start the steering / control unit
Press the ON/OFF button (2) and the operating display (6) will briefly flash on and the
screen will show the drive level (1-5) last used.
Switch off the steering / control unit
Press the ON/OFF button (2) and the system will switch off.
Lock the steering / control unit
If you keep the ON/OFF button (2) pressed for longer than 4 seconds, the operator control
will be locked.
The lock symbol will briefly appear in the display.
Unlock the steering / control unit
When the ON/OFF button (2) is pressed ...
... the lock symbol will appear in the display.
When you press the horn button (5) twice while the lock symbol is showing, the control
unit will be unlocked. The drive level (1-5) last used will appear in the display (1-5).
Switch the indicators on/off
To switch the drive direction display on and off, press buttons (3) or (4) for whichever
indicator you wish, left or right. When you activate a drive direction, it will flash in the status
display.
or
4 secs.
2 x
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vermeiren Controleunit DX2 Basic bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vermeiren Controleunit DX2 Basic in de taal/talen: Engels als bijlage per email.

De handleiding is 1,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Vermeiren Controleunit DX2 Basic

Vermeiren Controleunit DX2 Basic Gebruiksaanwijzing - Nederlands - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info