585216
6
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
HAM982K 6 VELLEMAN
7. Factory Settings
These are the factory settings – they can be modified if they are not applicable for your situation. Refer to the next
chapter ("8. Programming the Panel") for details on how to modify the settings.
The factory settings allow for the system to be operated as a local alarm panel without programming except for the
master and user codes.
LOCATION PARAMETERS DEFAULT PRESETS PROGRAM DATA
01 master code 1234 code=1234
11-18 user code 1-8 nil nil
21 zone 1 multiple trigger, entry delay 1, 500ms response code1=1, code2=1, code3=2
22 zone 2 multiple trigger, entry delay 1, 500ms response code1=1, code2=1, code3=2
23 zone 3 multiple trigger, instant, 500ms response code1=1, code2=0, code3=2
24 zone 4 multiple trigger, instant, 500ms response code1=1, code2=0, code3=2
25 zone 5 multiple trigger, instant, 500ms response code1=1, code2=0, code3=2
26 zone 6 multiple trigger, instant, 500ms response code1=1, code2=0, code3=2
27 zone 7 multiple trigger, 24hr instant, 500ms response code1=1, code2=3, code3=2
28 zone 8 multiple trigger, 24hr instant, 500ms response code1=1, code2=3, code3=2
30 exit delay exit beep enabled, 60 seconds code=1, duration=60
31 entry delay 1 entry beep enabled, 30 seconds code=1, duration=30
32 entry delay 2 entry beep enabled, 60 seconds code=1, duration=60
33 siren duration arm-disarm ring-back disabled, 300 seconds code=0, duration=300
40 arming type forced to arm code=0
41 alarm handover disabled code=0
HOME isolation zones in memory nil nil
85 power up delay disabled code=0
86 periodic battery test disabled code=0
8. Programming the Panel
BEWARE: to avoid triggering by the tamper switch, make sure the cabinet is firmly closed before applying power to
the system. Also, do not install a battery after power-on but before a user code is programmed: the tamper switch will
trigger the alarm instantly, but there is no user code to turn it off and the master code cannot be used for disarming.
The panel can be programmed from the system keypad. Enter programming mode, then key in the 2-digit
Programming Location or address, followed immediately by the desired programming values (program data), then
press the '#' key to store the data. The system will either confirm storage with 2 beeps, or signal an unsuccessful
storage attempt with 5 beeps. If you are not sure of the values that have been entered, program the programming
location again. When programming is finished, press the '' key twice to exit the programming mode.
a. Enter Programming mode
To enter the programming mode, enter either the factory set master code (1234) or your own master code (when
set), then press the '' key twice to confirm your entry. The console will beep twice to confirm that the system is in
programming mode – the PROGRAM LED will light up.
If the factory set master code was replaced and the new master code is lost, use the DAP jumper to override the
entry code and enter the programming mode directly. The DAP jumper is located on the master circuit board. Follow
this procedure precisely to use the DAP jumper:
1) Disconnect the power supply including both AC power and the backup battery.
2) Set the jumper from the OFF to the ON position.
3) Reconnect the power supply, the console will beep continuously.
4) Put the DAP jumper back to OFF ; the beeping stops and the PROGRAM LED is on.
5) The system is now in programming mode and ready to receive new data.
6) The DAP jumper should be left in the OFF position after programming.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Velleman HAM982K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Velleman HAM982K in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info