585216
5
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
HAM982K 5 VELLEMAN
8 Common ground
9 This terminal provides +12V output power upon alarm condition during the time period set in the alarm timer. It
is ideal for a siren or alarm bell. The output is equipped with a 2.5A resettable fuse.
10-13 These terminals are the connection points for remote switches for arm-disarm control (optional). These
switches need to be of the 'momentary contact' type and equipped with 2 LEDs (home/away LED and status
LED). Up to 3 of these switches can be connected in parallel. Switches that can be used are HAA80 (key
switch), HAA85 (security keypad) and HAA85WP (security keypad – waterproof).
10: to connect the actual key switch contact(s)
11: to connect the home/away LED(s): away= all zones are activated ; home= only the selected zones are
activated (see "8.l.Setting "HOME" mode") – the other zones are freely accessible.
12: to connect the status LED(s)
13: +12V common point for contacts and LEDs, equipped with a 750mA resettable fuse.
switch contact status results
ARMING THE SYSTEM
1
st
contact away mode arming
Exit delay starts
Exit beep sounds if it is enabled
The system will be armed after exit delay
2
nd
contact home mode arming
The 2
nd
touch must be made within the exit delay period
Exit beep sounds continuously during exit delay
The system will be armed after exit delay
DISARMING THE SYSTEM
1
st
contact system disarmed
The system is disarmed and reset if there was no
alarm. It is ready for rearming.
The system is disarmed but with alarm memory if an
alarm occurred – 2
nd
contact is required
2
nd
contact
alarm memory is cleared
system remains disarmed
The alarm memory LEDs are off ('status' LED + zone
LEDS). The system is ready for rearming.
LED on off flashing
home-away away mode system disarmed home mode
status
exit delay starts but there
is/are (an) unsealed zone(s)
– check zone connections
system is armed after exit
delay expired
system disarmed
Flashing slow: exit delay starts and
the zones are normal
Flashing fast: zone is or was in alarm
Flashing fast with intervals: system is
disarmed or zone with alarm memory.
14-16 These terminals have no function.
17-28 These terminals are protection zones 1-8 and their common ground
terminals. The zones are EOL (End of Line), with a 2.2k resistor.
NC (normally closed) contacts are to be wired in series with the EOL
resistor, whereas NO (normally open) contacts are to be wired in parallel with the EOL resistor. The function of
the zones and their response times are programmable via the system programming options.
17=zone 1 ; 19=zone 2 ; 20=zone 3 ; 22=zone 4 ; 23=zone 5 ; 25=zone 6 ; 26=zone 7 ; 28=zone 8.
18, 21, 24, 27: common ground.
IMPORTANT: the cabinet's (NC) tamper switch is pre-wired to zone 8 internally. We suggest you always keep
zone 8 as a 24h protection zone.
DAP jumper: DAP means Direct Access to Programming: this jumper is provided to set the system in programming
mode in case the master code is forgotten or lost.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Velleman HAM982K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Velleman HAM982K in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info