809802

VTech AM706-1W Handleiding

1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Caution
• The default volume of your parent unit is level 3. If you experience feedback from your baby monitor
while positioning:
- Make sure your baby unit and parent unit are more than 2 metres apart, OR
- Turn down the volume of your parent unit.
Operating range
The operating range of the baby monitor is up to 300 metres outdoors or 50 metres indoors.
The actual operating range may vary depending on the environmental conditions, and other
interferences such as walls, doors, and other obstructions.
Install the parent unit battery
The parent unit runs on rechargeable battery or AC power. To continuously monitor your
baby, keep the parent unit connected to AC power. With the battery alone, the parent unit
can cordlessly run for a short time only.
NOTESNOTE
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.
Replace the battery
To replace the battery, unplug the battery connector from the socket, and then pull the
battery out of the battery compartment. Follow the steps above to install the battery.
Connect the baby monitor
NOTESNOTE
• Use only the power adaptors supplied with this product.
• Make sure the baby monitor is not connected to an electric outlet that is controlled by a switch.
• Connect the power adaptors in a vertical or floor mount position only. The adaptors’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,
or cabinet outlets. Otherwise, the adaptors may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adaptor cords are out of reach of children.
• With audio reminder feature preset to ON, the parent unit plays an audio reminder when it is
connected to a baby unit.
Charge the parent unit battery
When you have connected the parent unit and installed its battery for the first time or after
power outage, the parent unit powers on automatically. The battery icon indicates the
battery status (see the following table).
User’s manual
AM706-1W
Digital Audio Monitor
What’s in the box
1
Connect and charge the battery
NOTESNOTE
Notes
• The parent unit battery is fully charged after 11 hours of continuous charging.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,
turn the parent unit off while charging.
• The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.
Battery indicators Battery status Action
The battery icon is off. No battery is installed but
operates using AC power.
Install the parent unit battery.
Charge without interruption (at least
30 minutes).
The screen displays LOW
BATTERY and . The light
flashes.
The battery has very little
charge and may be used
for only a short time.
Charge
without interruption
(about
30 minutes).
The battery icon becomes
solid .
The battery is fully charged. To keep the battery charged, connect
it to AC power when not in use.
Battery Pack / Bloc-piles :
BT183342/BT283342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR0920
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
THIS SIDE UP
2
:
AVERTISSEMENT :
THIS SIDE UP / CE CÔTÉ
:
AVERTISSEMENT :
TTERI
HIS SIDE UP / CE CÔTÉ VERS L
1
2
3
NOTESNOTE
Note
Make sure the label
THIS SIDE UP is facing
up while inserting the
battery.
4
1
2
1
2
LINKED
LINKED
LINKED
2m
>
Note
• This baby monitor should be for use by adults only.
• It is not a substitute for proper adult supervision, and should not be used as such.
Test your audio monitor
You may test the baby monitor before initial use, and at regular times thereafter.
Caution
• For hearing protection, make sure the parent unit is more than
2 metres away from the baby unit. If you hear any
feedback, move the parent unit further until the noise stops. You
can also press on the parent unit to lower or mute the noise.
1. Make sure your baby unit and parent unit are on.
2. Speak towards the microphone of the baby unit. You will
hear the sound at the parent unit, and see the visual sound
indicators light up.
Note
• When the parent unit displays NOT LINKED and flashes, move the parent unit closer to the baby unit
(observe the minimum distance of 2 metres).
Tip
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the
baby unit.
Positioning the baby monitor
Caution
• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the
baby’s cot or playpen.
1. Place the baby unit more than 1 metre away from your baby.
2. Place the parent unit more than 2 metres away from the baby unit.
2
Before use
> 1m
1
> 2m
2m
<
2
Using the baby monitor
Power on or off the baby unit
• Press and hold POWER to power on the baby unit. The power light
turns on.
• Press and hold POWER to power off the baby unit. The power
light turns off.
Power on or off the parent unit
• Press and hold POWER to power on the parent unit. The screen
turns on.
• Press and hold POWER again to power off the parent unit. The
screen turns off.
Note
• The parent unit powers on automatically once it is connected to power
socket or battery installed. The baby unit also powers on automatically once
connected to power socket.
Adjust the speaker volume for baby unit
• Press VOLUME or VOLUME on the baby unit at any time.
Note
• The speaker of baby unit cannot be muted.
Adjust the speaker volume for baby unit using parent unit
The baby unit volume can also be adjusted in the parent unit.
1. Press when the parent unit is not in use.
2. Press or to scroll to BABY VOLUME, then press .
3. Press or to choose the desired volume level. VOLUME 1 is the softest while
VOLUME 5 is the loudest.
4. Press to confirm your selection. The screen displays SAVED and you hear a
confirmation tone.
Adjust the speaker volume for parent unit
You can adjust the speaker volume from VOLUME 1 to VOLUME 5, or turn it off. The speaker
volume is preset to VOLUME 3.
• Press or when the parent unit is not in use.
When the speaker volume is set to off, the screen displays .
Adjust the Voice-activated (VOX) sensitivity level of the baby unit
You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a
certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit.
The higher the VOX sensitivity level, the more sensitive the baby unit is in detecting sounds for
transmitting to the parent unit. The VOX sensitivity level is preset to HIGHEST.
VOX
Sensitivity
level
Highest High Medium Low Lowest
Description The parent
unit speaker
is constantly
on, and you
will hear
all sounds
(including
background
noises) from
your baby’s
room.
The parent
unit speaker
turns on for
soft babbling
and louder
sounds from
your baby. It
remains quiet
when your
baby sleeps
soundly.
The parent
unit speaker
turns on
for loud
babbling
and louder
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
The parent
unit speaker
turns on
for crying
and louder
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
The parent
unit speaker
turns on for
loud crying
or screeching
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
1. Press when the parent unit is not in use.
2. Press or to scroll to SENSITIVITY, then press .
3. Press or to choose the VOX sensitivity level.
4. Press to confirm your selection. The screen displays SAVED and you hear a
confirmation tone.
Note
• To enter the VOX Level menu of the parent unit, the baby unit must be turned on.
Sound alert
If you turn on the sound alert, the parent unit beeps when the baby unit detects sounds
which had triggered the red light of visual sound indicator on the parent unit.
When the sound alert of the parent unit is turned on, is shown on LCD display. The
sound alert is preset to OFF.
1. Press when the parent unit is not in use.
2. Press or to choose SOUND ALERT, then press . The screen displays ON? or
OFF?.
3. Press to confirm your selection. The screen displays SAVED and you hear a
confirmation tone.
Note
• The sound alert setting on each parent unit is independent.
Vibration alert
You can turn on the vibration alert so that the parent unit vibrates when the baby unit detects
sounds which had triggered the red light of visual sound indicator on the parent unit.
When the vibration alert of the parent unit is turned on, is shown on LCD display. The
vibration alert is preset to OFF.
1. Press when the parent unit is not in use.
2. Press or to choose VIBRATOR, then press . The screen displays ON? or OFF?.
3. Press to confirm your selection. The screen displays SAVED and you hear a
confirmation tone.
Notes
• Each time you set the vibration alert to ON, the parent unit vibrates briefly after you press .
• The vibration alert setting on each parent unit is independent.
Lullaby
The baby monitor has five lullabies for you to comfort your baby. You can play or stop
lullabies on the baby unit by controlling remotely with the parent unit.
1. Press when the parent unit is not in use.
2. Press or to choose LULLABY, then press .
3. Press or to choose a lullaby, or choose PLAY ALL, then press . The screen
displays PLAY or STOP.
4. Press to confirm your selection. The screen displays SAVED and you hear a
confirmation tone.
Notes
• If you choose a lullaby, the selected lullaby will be played repeatedly for about 20 minutes.
• If PLAY ALL is selected, the five lullabies will be played one after the other, until all of them are played.
• When the lullaby is playing, the parent unit displays the name of the selected lullaby, or PLAY ALL on the
idle screen.
Turn on or off the glow-on-ceiling night light
You can turn on the glow-on-ceiling night light on the baby unit. The baby unit projects a
starry night scene onto the ceiling.
When the glow-on-ceiling night light is turned on, displays on the parent unit screen.
Turn on/off the night light using the baby unit:
1. Press to turn on the night light.
2. Press again to turn off the night light.
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 1921.536-1928.448 MHz
Parent unit: 1921.536-1928.448 MHz
Maximum power used by the transmitter: 0.25W (250mW)
Channels 5
LCD 35 (x) x 21.2 (y) mm B&W LCD
Nominal effective range Actual operating range may vary according to environmental
conditions at the time of use.
Power requirement Parent unit: 2.4 V Ni-MH battery
Baby unit power adaptor:
Output: 6V DC 450mA
Parent unit power adaptor:
Output: 6V DC 450mA
Technical specifications
Specifications are subject to change without notice.
© 2021 VTech Communications, Inc.
All rights reserved. 07/21. AM706-1W_UK_CIB_V4
The applied nameplate is located at the bottom of the baby
unit’s base.
When using your equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock
and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above
2 metres.
4. This product is not a substitute for adult supervision of
the infant. Supervising the infant is the responsibility of
the parent or carer. This product could cease operating,
and therefore you should not assume it will continue
working properly for any given period of time. Further,
this is not a medical device and should not be used as
such. This product is intended to assist you in supervising
your baby.
5. Do not use this product near water, for example, near to a
bath, sink, swimming pool or shower.
6. CAUTION: Use only the battery provided. There may be
a risk of explosion if a wrong type of battery is used for
the parent unit. The battery cannot be subjected to high
or low extreme temperature and low air pressure at high
altitude during use, storage or transportation. Disposal of
battery into fire or a hot oven, or mechanically crushing or
cutting or the battery can result in an explosion. Leaving
the battery in an extremely high temperature surrounding
environment can result in an explosion or the leakage of
flammable liquid of gas. Battery subjected to extremely
low air pressure may result in an explosion or the leakage of
flammable liquid or gas. Dispose of used battery according
to the instructions.
8. Use only the adaptors included with this product. Incorrect
adaptor polarity or voltage can seriously damage the
product.
Use only adaptors and battery listed below.
Power adaptor information:
Ten Pao Industrial Co.,Ltd.
Model : S003ATB0600045 (UK)
Vtech Telecommunications Limited.
Model: VT05EEU06045 (EU), VT05EUK06045
(UK,alternative)
Rechargeable battery information:
Corun - Ni-MH AAA400X2-CB
Ni-MH AAA400mAh 2.4V.
9. The power adaptors are intended to be correctly oriented
in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
10. For pluggable equipment, the socket-outlet should
be installed near the equipment and should be easily
accessible.
11. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
12. Unplug the power cords before replacing batteries.
13. Do not cut off the power adaptors to replace them with
other plugs, as this causes a hazardous situation.
14. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
15. This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply in your home, consult
your dealer or local power company.
16. Do not overload wall outlets or use an extension cord.
17. Do not place this product on an unstable table, shelf, stand
or other unstable surfaces.
18. This product should not be placed in any area where
proper ventilation is not provided. Slots and openings
in the back or bottom of this product are provided for
ventilation. To protect them from overheating, these
openings must not be blocked by placing the product on a
soft surface such as a bed, sofa or rug. This product should
never be placed near or over a radiator or heat source.
19. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage points
or create a short circuit. Never spill liquid of any kind on the
product.
20. To reduce the risk of electric shock, do not disassemble
this product, but take it to an authorized service facility.
Opening or removing parts of the product other than
specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently used.
21. You should test the sound reception every time you turn on
the units or move one of the components.
22. Periodically examine all components for damage.
23. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless
telephones, etc. To protect your privacy, make sure the
product has never been used before purchase, reset
the baby monitor periodically by powering off and then
powering on the units, and power off the baby monitor if
you will not use it for some time.
24. Children should be supervised to ensure that they do not
play with the product.
25. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 0oC
and 40oC.
2. Do not expose the product to extreme
cold, heat or direct sunlight. Do not put the
product close to a heating source.
3. Batteries should not be exposed to excessive
heat such as bright sunshine or fire.
4. Warning—Strangulation Hazard—Children have
STRANGLED in cords. Keep this cord out of the reach of
children (more than 0.9 m away). Do not remove this tag.
5. Never place the baby unit inside the baby’s cot or playpen.
Never cover the baby unit or parent unit with anything such
as a towel or a blanket.
6. Other electronic products may cause interference with your
baby monitor. Try installing your baby monitor as far away
from these electronic devices as possible: wireless routers,
radios, cellular telephones, intercoms, room monitors,
televisions, personal computers, kitchen appliances and
cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the
pacemaker.
• Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and
according to the instructions in this user’s manual, the product is
safe to be used based on scientific evidence available today.
Important safety instructions
2 Before use (Cont'd)
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VTech AM706-1W bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VTech AM706-1W in de taal/talen: Engels als bijlage per email.

De handleiding is 6.86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info