809802

VTech AM706-1W Handleiding

2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Baby unit overview
1Glow-on-ceiling night light
2
• Press to turn on or off the glow-on-
ceiling night light.
3VOLUME
• Press to increase the speaker
volume.
4VOLUME
• Press to decrease the speaker
volume.
5Microphone
6Power light
• On when the baby unit is turned on.
7POWER
• Press and hold to power on, and the
power light turns on.
• Press and hold to power off, and
the power light turns off.
8Power jack
9Speaker
10 Temperature sensor
Parent unit overview
Below are the questions most frequently asked about the baby monitor.
Why does the baby
monitor not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby unit and the parent unit.
2. Remove the batteries in the parent unit. Then, install the batteries again.
3. Wait a few minutes before connecting power back to the baby unit and the parent unit.
4. Turn on the baby unit and the parent unit.
5. Wait for the parent unit to synchronize with the baby unit. Allow up to one minute for
this to take place.
Why doesn’t the screen
of the parent unit go on
when I switch on the unit?
Perhaps the rechargeable battery of the parent unit is empty and the parent unit is not
connected to the power. Insert the appliance plug into the parent unit and put the
adaptor in a wall socket.
Why doesn’t the power
light of the baby unit go on
when I switch on the unit?
Perhaps the baby unit is not connected to the power. Connect the baby unit to the
power.
Why does the baby
monitor produce a
high-pitched noise?
The units may be too close to each other. Make sure the parent unit and the baby unit
are more than 2 metres away from each other.
Why does the parent unit
react too quickly to other
sounds?
The baby unit also detects other sounds than those of your baby. Adjust the VOX
sensitivity level to a lower level or adjust the speaker volume on the parent unit.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
The volume of the parent unit may have set too low. Press to increase the volume level.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby
unit to change the setting.
Why does the parent unit
beep?
If the sound alert feature is on, there is sound detected from the baby unit.
The baby unit may be out of range. Move the parent unit closer to the baby unit (but not
less than 2 metres).
If the parent unit is powered by the provided battery, it may not have enough charge for
the parent unit to perform normally. Charge the battery in the parent unit for up to 11 hours.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby unit may be out of range. Move the parent unit closer to the baby unit (but not
less than 2 metres).
Other electronic products may cause interference with your baby monitor. Try installing
your baby monitor as far away from these electronic devices as possible.
Why doesn’t the battery
icon shown on LCD display
even I have properly
installed the battery?
The battery may not be working. Contact our customer service to purchase a new
battery.
Frequently asked questions
When you are not going to use the baby monitor for some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and the adaptors in a cool and dry place.
Storage
To keep this product working well and looking good, follow these guidelines:
• Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors
or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft damp cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under running water.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
General product care
Parent unit icons
Status icons
Connection status
• displays when strong signal
strength is detected between the
baby unit and the parent unit.
• displays when moderate signal
strength is detected between the
baby unit and the parent unit.
• displays when the weak signal
strength is detected between the
baby unit and the parent unit.
• flashes when the link between
the baby unit and the parent unit
is lost.
Full ECO mode
• Displays when Full ECO Mode is
turned on.
Glow-on-ceiling night light
• Displays when the glow-on-ceiling
night light of the baby unit is on.
Sound alert
• Displays when the sound alert of
the parent unit is turned on.
• Flashes when there are loud
sounds detected from the baby
unit.
Vibration alert
• Displays when the vibration alert
of the parent unit is turned on.
• Flashes when there are loud
sounds detected from the baby
unit.
Mute
• Displays when the patient unit
speaker volume is turned off.
Battery status
• animates when
the battery is charging.
• displays solid when the battery
is fully charged.
• flashes when the battery is
charged with AC adaptor, or
charging is failed.
• flashes when the battery is in
low level and needs charging.
• No battery icon displays when
there is no battery installed.
1Visual sound indicator
The visual sound indicator shows the
sound level detected by the baby unit.
• One to three green
lights indicate a moderate sound
level detected by the baby unit.
• Additional red
lights indicate a higher sound level
detected by the baby unit (e.g. baby
crying loudly).
2LCD display
3Microphone
4
• Press to decrease the speaker
volume.
• Press repeatedly until the volume
reaches the minimum to turn it off.
• While in a menu, press to scroll down.
5Speaker
6
• Press to enter the menu.
• While in a menu, press to choose an
item, or save a setting.
7 Battery LED
• Light on when the battery is being
charged.
• Light flashes when the battery is low
and needs charging.
• Light off when the parent unit is
running on AC power without
battery installed, or the parent unit is
running on battery only.
8
• Press to increase the speaker volume.
• While in a menu, press to scroll up.
9
• While in a menu, press to return to
the previous menu.
10 POWER
• Press and hold to power on, the
screen turns on.
• Press and hold again to power off,
the screen turns off.
• While in a menu, press to return to
idle screen.
11 TALK
• Press and hold to talk to the baby.
12 Power jack
13 Belt clip
14 Battery compartment cover
Declaration of Conformity
The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging,
indicates they must not be disposed of in domestic waste as they contain substances that can be
damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more
than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive
(2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
Disposal of batteries and productCustomer service and product warranty
5. Press to confirm your selection, The screen displays SAVED. You hear a
confirmation tone.
Set temperature alert tone
You can turn on the temperature alert tone so that the parent unit will emit an alert tone if
the detected temperature is out of range.
1. Press when the parent unit is not in use.
2. Press or to scroll to TEMPERATURE, then press .
3. Press or to choose ALERT ON/OFF, then press . The screen displays ON? or
OFF?.
4. Press to confirm your selection, The screen displays SAVED. You hear a
confirmation tone.
Extended ECO
You can turn on the extended ECO mode so that the radiation emitted will be lowered to
the minimum, so as the operating range will be reduced to the minimum.
1. Press when the parent unit is not in use.
2. Press or to scroll to EXTENDED ECO, then press . The screen displays ON? or
OFF?.
3. Press to confirm your selection. The screen displays SAVED and you hear
a confirmation tone.
ECO range
You can change the setting of the ECO range. The shorter the ECO range, the lower the
radiation will be emitted, so as the operating range will be reduced.
1. Press when the parent unit is not in use.
2. Press or to scroll to ECO RANGE, then press .
3. Press or to choose AUTO, BIG ROOM or SMALL ROOM.
4. Press to confirm your selection. The screen displays SAVED. You hear a
confirmation tone.
Set default
Use this feature to restore to the default settings. Restoring the default settings on one parent
unit will also reset the shared settings for VOX sensitivity level of the other parent unit.
1. Press when the parent unit is not in use.
2. Press or to choose RESET, then press . The screen displays CONFIRM?.
3. Press or to choose YES or NO.
4. Press to confirm your selection. The screen displays SAVED. You hear a
confirmation tone.
-OR-
Press to exit the menu. The current setting remains unchanged.
3
Using the baby monitor (Cont’d)
Talk to the baby unit
You can broadcast messages from a parent unit to the baby unit and the other parent unit.
• Press and hold TALK on the side of the parent unit. The screen displays when the
voice connection to the baby unit is made. Speak towards the MIC on the parent unit.
Your voice is broadcast to the baby unit.
Notes
• When a parent unit is talking to the baby unit, sounds from the baby unit cannot be transmitted to the
parent unit at the moment.
• If speaker volume of the parent unit has been turned off before the talk, it will change to default
volume level after the talk finished.
Parent unit display screen messages
LINKED • The link between
the parent unit and
the baby unit is
established.
LOW BATTERY • The parent unit uses
only the rechargeable
battery pack and
it needs to be
recharged.
NOT LINKED • The link between
the parent unit and
the baby unit is lost
continuously for over
10 seconds.
SAVED • Your selection has
been saved.
SEARCHING • The parent unit is out
of range of the baby
unit, or the baby unit
is out of power.
TALK • You are using the
parent unit to talk to
your baby.
HI TEMP • The temperature
detected from
the selected baby
unit is above the
set maximum
temperature.
LOW TEMP • The temperature
detected from
the selected baby
unit is below the
set minimum
temperature.
oF / oC • The real-time
temperature detected
by the baby unit in
Fahrenheit (oF) or
Celsius (oC).
Turn on/off the night light using the parent unit:
1. Press when the parent unit is not in use.
2. Press or to choose NIGHTLIGHT, then press .
The screen displays ON? or OFF?.
3. Press to confirm your selection. The screen displays
SAVED and you hear a confirmation tone.
Notes
• The night light on baby unit operates even when the parent unit
battery is out of charge or has been turned off.
• If the parent unit lost link, the night light icon on its LCD display will
disappear, regardless of the night light status.
Language
You can select a language to be used in all screen displays.
1. Press when the parent unit is not in use.
2. Press or to choose LANGUAGE, then press .
3. Press or to choose a language.
4. Press to confirm your selection. The screen displays SAVED and you hear
a confirmation tone.
Note
• The language setting on each parent unit is independent.
Temperature
Your baby unit monitors the temperature of your baby’s room with its built-in
temperature sensor. If the detected temperature is out of the preset temperature range,
the parent unit will display an alert message.
Set temperature format:
You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC).
1. Press when the parent unit is not in use.
2. Press or to scroll to TEMPERATURE, then press .
3. Press or to choose FORMAT, then press . The screen colours FAHRENHEIT?
or CELSIUS?.
4. Press to confirm your selection, The screen displays SAVED and you hear a
confirmation tone.
Set temperature range:
You can set the desired room temperature alert range. The minimum temperature can be
set between 10oC and 20 oC. The maximum temperature can be set between 21 oC and 30
oC.
1. Press when the parent unit is not in use.
2. Press or to scroll to TEMPERATURE, then press .
3. Press or to choose MINIMUM or MAXIMUM, then press .
4. Press or to choose the desired minimum or maximum temperature.
This product is intended for use within Europe and UK.
This equipment complies with the essential requirements to EU’s Radio Equipment
Directive (2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and
telecommunication equipment.
VTech Telecommunications Ltd. hereby declares that
this Audio Monitor AM706-1W is in compliance with the essential requirements and
other relevant provisions of EU’s Radio Equipment Directive (2014/53/EU) and UK’s Radio
Equipment Regulations 2017.
The Declaration of Conformity for the AM706-1W is available from
www.vtechbabycare.com.
Manufacturer: VTech Telecommunications Ltd.
23/F., Tai Ping Industrial Centre, Block 1, 57 Ting kok Road, Tai Po, Hong Kong.
Importer: VTech Electronics Europe Plc
Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service
Please call our Consumer Services Department on 03306 780149 (from UK) or
+44 3306 780149 (outside UK) and a service representative will be happy to help you.
This warranty is valid for the UK and Ireland only. For products purchased outside
the UK and Ireland, please contact your local distributor or place of purchase.
P
R
O
D
U
C
T
W
A
R
R
A
N
T
Y
ONE
YEAR
PRODUCT WARRANTY
Thank you for choosing this quality product from VTech.
1.The product detailed above is covered by a one year warranty from the date of purchase,
against any defects in materials or workmanship.
2.The product may be returned to the place of purchase. Alternatively the product can be
returned to VTech Electronics Europe Plc (see address below), with proof of purchase,
without proof of purchase no replacement will be provided.
3.VTech Electronics Europe Plc will examine the product and if it is found to be defective
due to faulty materials or workmanship, will replace the product at their discretion.
4.If the product covered by this warranty is damaged due to misuse, modification or
unauthorized repair, or because of faulty batteries, battery discharge or incorrect
electrical connections, then this warranty becomes void.
5.This warranty is personal to the original purchaser and is not transferable.
6.Breakages to the LCD screen are not covered by the warranty.
7.Products returned to VTech Electronics Europe Plc, should be sent to the address shown
below and packed carefully to avoid damage in transit. Please do not include batteries or
adaptors. Please include details of the fault together with your name and address,
contact phone number and/or email address.
8.To keep an online record of your warranty, please register your product online at
www.vtech.co.uk/clubvtech
VTech Electronics Europe Plc, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane,
West Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT
CONSUMERS’ STATUTORY RIGHTS.
UK
PRODUCT REGISTRATION
Visit www.vtech.co.uk/clubvtech/login
to register your VTech product
By joining the VTech Club you can also enter competitions,
find out about news and events, seek expert advice for parents
and let your kids play fun learning games and activities.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VTech AM706-1W bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VTech AM706-1W in de taal/talen: Engels als bijlage per email.

De handleiding is 6.86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info