484649
16
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
16
Remote hand set LED flash codes and
acoustic signal
LED “On“ and no acoustic signal
System is ready for operation
LED “Off” and no acoustic signal
System off
(check remote hand set batteries if necessary)
LED “flashes” in combination with acoustic signal
for approx. 5 seconds after switching the remote hand set
on, until the system is ready for operation.
for approx. 10 seconds after switching the remote hand set
on, then it is switched off again – 13-pin safety plug not
connected to safety socket or unable to establish radio link
to controller.
every 3 seconds if the caravan battery has a low charge
(finish manoeuvring as quickly as possible and charge
battery).
5 times a second (5 Hz) if the caravan battery voltage is
low. No manoeuvring is possible until the battery voltage is
above 11 V again (e.g. by means of recovery / battery charg-
ing). The drive rollers can also be disengaged with a voltage
of less than 11 V.
approx. 2 times per second with overcurrent / over-
temperature (2 Hz). Switch remote hand set off and on
again (wait for cooling down if necessary in the event of
overtemperature).
Changing the batteries in the remote handset
Please be sure to use leak proof micro-
batteries only, type LR 03, AAA, AM 4,
MN 2400 (1.5 V).
When fitting new batteries
ensure the polarity is correct!
Dead and used batteries may
leak and damage the remote
handset! Remove the batteries if the
handset is not going to be used for an
extended period.
No claims under guarantee will be considered for damage
caused by leaking batteries.
Before throwing away a defective handset, it is essential that
the batteries are removed and disposed of in proper manner.
Manoeuvring the caravan
Please read the “Safety instructions” before using
the Mover®!
Apply handbrake with caravan uncoupled.
Unplug 13-pin plug from vehicle and plug into safety socket of
caravan.
For safety reasons the Mover® can only be operated if
the 13-pin plug of the caravan has been plugged into the
safety socket.
In the event of an error, the 13-pin plug should not be
removed from the safety socket as otherwise the elec-
tronic protection function is deactivated.
If there is a fault in both caravan brake lights, the power
circuit of the safety socket is not closed. In this case the
Mover® cannot be operated.
Switch on remote control – green LED flashes in combination
with the signal tone approx. 5 seconds until both control sys-
tems are operational.
Simultaneously press the two buttons (h) for engaging, which
starts after approx. 3 seconds (safety delay).
Using the position display, check whether the 4 drive
rollers are in the correct position (arrow of the yellow
position indicator stands above the line that is next to the
closest tyre).
Before operating the Mover®, release the handbrake.
The six direction buttons provide movement in six directions –
forward, reverse, left forward, left reverse, right forward, right
reverse.
With the Mover® SE R, the “left forward” (e) and “right
reverse” (f) or “right forward” (d) and “left reverse” (g) buttons
can also be pressed simultaneously in order to turn the cara-
van in a circle on the spot without moving it forwards.
The soft start / stop facility means that the caravan starts
without jerking and is gently braked when stopping.
If the buttons are released or the radio signal is interfered with
or becomes too weak, the caravan stops. Your Mover® cannot
be activated by radio devices or other Mover® remote hand
sets.
After starting up, the Mover® moves at a uniform speed. The
speed will increase a little when going downhill and decrease
a little when going uphill.
After manoeuvring, first apply the handbrake and then dis-
engage the drive rollers from the tyres.
Move slide switch on remote control to the “Off” £ position
to switch the remote control and the Mover® off.
The slide switch also acts as an “Emergency stop”
switch.
Remove plug from safety socket after manoeuvring, otherwise
the battery will be discharged. Standby current with plug
inserted approx. 300 mA.
Hitching to a tow car
It is totally possible to position the caravan’s hitch to a
stationary car tow ball using the Mover®, but take some care.
Use the instructions above as your guide. Use the button con-
trols to bring the caravan to the car (car handbrake “ON“, and
car in gear). Use a button stabbing technique to exactly posi-
tion the hitch directly over the ball. Lower the hitch to the ball
and engage in the normal way using the jockey wheel.
Prepare the caravan for towing as usual. The caravan must
never be towed with the drive rollers engaged.
Maintenance
Please do not allow the drive units to become soiled with
coarse road material. When you are cleaning the caravan,
spray the Mover® with a water hose to dissolve mud etc.
Please ensure that no stones, twigs or the like become
trapped in the equipment. The control unit does not require
maintenance. Please keep the remote hand set in a dry place.
Every year (and/or before putting away for the winter), clean
Mover® as described, dry and lightly spray the drive unit
guides with oil spray or a similar water-repelling lubricant. Do
not put lubricant on the rollers or the tyres! Engage and
disengage the drive units several times to allow the lubricant
to penetrate all the guides. Do not park the caravan with the
drive rollers engaged.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Truma Mover Mover TE R4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Truma Mover Mover TE R4 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Deens als bijlage per email.

De handleiding is 12,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info