607258
22
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
Page 22
12. POSSIBILITIES FOR CONNECTING THE CONCENTRIC FLUE SYSTEM
12.1 Direct exterior wall duct (see page: 26, figure 1.2).
Determine the position of the unit and close the exterior wall duct. When placing directly against the exterior wall
(e.g. cavity wall) ensure the exterior wall duct (Y Max) is shortened, but only if required. In all installation situa-
tions, take into account the possible application of the radiation plate delivered with the unit.
12.2 Indirect exterior wall duct (see page: 26, figure 1.3 and 1.4).
Always fit a length of X=1 metre vertical on the unit, followed directly by a bend of 90° with a length of X=1
metre and the wall terminal. The horizontal part can be extended to 4 metres plus wall duct (Y maximum) if re-
quired. From 1 metres to 4 metres the restriction plate (O) should be mounted.
12.3 Roof pass-through without slope (see page: 26, figure 1.5).
You can use a direct pipe layout without a slope for a maximum length of X=12 metres (excluding the roof termi-
nal) measured from the connection on the unit. The minimum length is 3 metres. You can have a flue terminal at
every position on the roof face (both flat and sloping); the flue exit and combustion air supply are located in the
same pressure area. Between 2 and 5 meters restrictor plate (O) should be mounted. . From 5 metres and above
the restriction plate (O) and restriction plate (P) should be mounted.
12.4 Roof pass-through with 45° slope (Refer to page: 26, figure 1.6).
Always fit a length of X=1 metre vertically on the unit. Next, continue building up the flue pipe using two 45°
bends (the calculation length for each bend is 1 metre) until you have reached the maximum pipe length of 12
metres (including bends, excluding roof pass-through). Between 2 and 5 metres the restrictor (O) should be
mounted. From 5 metres and above the restriction plate (O) and restriction plate (P) should be mounted.
12.5 Roof pass-through with 90° slope (see page: 26, figure 1.7).
Always fit a length of X=1 metre vertically on the unit. Next, continue building up the flue pipe using two 90°
bends (the calculation length for each bend is 2 metres) until you have reached the maximum pipe length of 12
metres (including bends excluding roof pass-through). Take into account a maximum horizontal layout of Y=4
metres (measured between bends) and also ensure sufficient gradient.
12.6 Connection to existing flue pipe.
See page 15 “INSTALLATION INSTRUCTIONS REGARDING EXISTING FLUES”
Use the special concentric connection pieces for existing ducts and keep strictly to the installation instructions.
12.7 Installing the restriction plate (O) and (P) duct (see page: 30)
Hold the ceramic baffle plate (G) with one hand while you remove the decoration strip (1) with the other
hand.
Slide the baffle plate a little forward so it comes out at the back from its fixture, after which it can be re-
moved from the unit.
Carefully remove the ceramic side walls (H) and (I).
Dismantle the baffle plate holder by loosening 2 bolts (3).
Place the restriction plate (O) behind the bracket. (Only when instructed)
Mount the restriction plate (P) to the restriction plate (O) with 2 parkers and place the entirety behind the
bracket. (Only when instructed)
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thermocet Estilo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thermocet Estilo in de taal/talen: Engels als bijlage per email.

De handleiding is 3,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info