607253
7
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
Page 7
3. Operating instruction for HB version.
Operating buttons and other functions of the gas control block BM 733
3.1 Switching on the unit
Open the gas shut-off cock that has been installed in the gas pipe to the unit.
Turn the operating button (A) from “Off” (C) position right round to the right until it stops.
Now press the button and turn to the left until the ignition position. You will now hear a click. This is a
spark ignition. You will be able to see whether the pilot is burning through the window. Click a few times if
required until the pilot lights up.
When the pilot is burning, hold the button pressed in for another 10 seconds and then let the button come
up slowly. Now the pilot must carry on burning.
If this is not the case then wait for one minute and repeat the procedure.
By turning the button to the left, the main burner is ignited and the desired flame height can be set.
In position “Pilot” (B) the main burner goes out and just the pilot remains burning.
3.2 Switching off the unit
In order to turn off the unit completely, press the operating button (A) in “Pilot” position and turn further to
the right until it stops and then release the button.
The pilot then goes out. We, however, recommend allowing the unit to burn with the pilot on during the pe-
riod of use.
If the fireplace will not be used for a longer period of time, we recommend also closing the gas shut-off
cock completely in the supply line.
A= Operating button B= Pilot ignition position C= Off
4. Installation instruction for flue version
General
Only have the unit installed and connected by a recognised fitter in accordance
with the locally applicable gas installation rules and regulations.
Never install the unit against or within a flammable wall.
Fit the apparatus on a non flammable floor. If you fit the apparatus on a wooden
floor or floor covering, it is preferable to use a steel floor plate which is available at our warehouse.
A chimney draught of approximately 0.5 mm water column is sufficient, measured at full load of the unit.
We recommend reducing the draught if the chimney draught is higher than 2 mm water column.
If a window fan has been installed in the room or if the unit is being installed in an insulated home, pressure
equalising openings to the outside air must also be installed. This is necessary to ensure that the chimney
continues to work should any underpressure occur.
We also recommend connecting gas heaters, gas inserts and gas built-in fireplaces to an outlet vent that is
made completely of 100 mm aluminium and/or stainless steel. This will ensure that there are no problems
with regard to the thermal outlet protection and other issues.
We also recommend using an aluminium and/or stainless steel flue lining when connecting to an existing
outlet vent in relation to a fireplace where before wood, coal or oil was burnt.
4.1 Fitting the unit
Fit the unit as tightly as possible to the flue so that a short, not corroding connection is made. Preferably without
bends. All in line with the locally applicable gas installation regulations.
The connections must be tension-free to ensure the gas regulating equipment is not damaged.
Check
Check the gas connections made to ensure that there is proper gastightness by using soapy water or a leak search
spray. Switch on the fireplace according to the operating instructions.
BM 733
P
I
L
O
T
OFF
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thermocet Coventry S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thermocet Coventry S in de taal/talen: Engels als bijlage per email.

De handleiding is 3,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info