514296
26
Verklein
Vergroot
Pagina terug
1/113
Pagina verder
eZ430-Chronos Sports Watch Software
www.ti.com
3.2.2 Detailed Feature Overview - Modes Using the Bottom LCD Line
3.2.2.1 Date Mode
Press "#" until the date mode is active (see Figure 3-1).
Secondary function: Year. Press "DOWN" to activate the alternative display. To return to day and month,
push the "DOWN" button again.
Set function: Setting the date
1. Push the "#" button until the date is displayed in the bottom LCD line.
2. Hold "#" for three seconds until the year flashes on the bottom LCD line.
3. Set the year by pushing the "UP" or "DOWN" button.
4. Press "#" to continue with the month adjustment.
5. Set the month by pushing the "UP" or "DOWN" button.
6. Press "#" to continue with the day adjustment.
7. Set the day by pushing the "UP" or "DOWN" button. Press "*" to confirm the settings and go back to
normal operation, or press "#" to start over with step 3.
NOTE: If no key is pressed for more than 30 seconds, the previous settings are restored.
3.2.2.2 Stopwatch Mode
Press "#" until the stopwatch mode is active (see Figure 3-1). It supports up time intervals up to 19 hours,
59 minutes and 59 seconds. For the first 20 minutes, the resolution is 1/100 second, after 20 minutes the
resolution changes to 1 second.
Secondary function: Start/stop. Press "DOWN" to start or stop the stopwatch
Set function: Reset stopwatch.
Hold the "#" button until the stopwatch is set to zero
3.2.2.3 Battery Voltage Mode
Press "#" until the battery voltage is shown (see Figure 3-1). It is updated once per minute.
Secondary function: None
Set function: None
3.2.2.4 Acceleration Mode - RF
This mode requires the eZ430-Chronos Control Center PC software.
Press "#" until "ACC" is shown on the LCD (see Figure 3-1). This mode provide a continuous transmission
of 3D acceleration from the watch using TI's SimpliciTI protocol stack. In addition, the watch transmits a
signal when the "#", "*" or "UP" buttons are pushed.
Secondary function: Start/stop transmission of acceleration data. Pushing "DOWN" starts/stops the
pairing process or stop the transmission (the access point on the PC must be started first from the
eZ430-Chronos Control Center (see Section 3.3.1). The RF icon on the LCD flashes when the radio is
active. If the pairing fails, it disappears. The top LCD line shows the time during the pairing and until the
data transmission is disabled.
Set function: None
26
eZ430-Chronos Software SLAU292DNovember 2009Revised March 2011
Submit Documentation Feedback
© 2009–2011, Texas Instruments Incorporated
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Texas Instruments eZ430-Chronos bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Texas Instruments eZ430-Chronos in de taal/talen: Engels als bijlage per email.

De handleiding is 7,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info